1021459-1-S-GE-WH10X10006        -Door Lock Latch
1021459-1-S-GE-WH10X10006        -Door Lock Latch 1021459-2-S-GE-WH10X10006        -Door Lock Latch 1021459-3-S-GE-WH10X10006        -Door Lock Latch

Door Lock Latch

PartSelect Number PS1021459

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Will Not Start.
  • Lid or door will not open.
  • Compare At

    $192.73
  • You Save

    $32.12
  • Your Price

    $160.61
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 3 reviews What's this?
1-3 of 3
 

23 of 28 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerAndrew from Dania FL

Machine would not function

Removed the three screws behind the top panel and slide it back to remove. Removed control panel then the two lower screws on the front panel the spring around the front of the gasket and slid up the front assembly to remove. Door lock was on front panel held by 2 screws and then loosened clamp around back of gasket and the gasket removed easily. The installation was easy nothing special to do and the problem was solved.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 12 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerElliot from North Port FL

Washer door would not lock / run. It just beeped twice.

Unplug the washer power cord. Take the screws off at the top (behind the front panel). Take the bolts off at the back (just the ones at the top). Remove the top cover. I'm going on memory here... Take the dial / knob off the front. Make sure the bottom of the control panel is free so the it's lip does not block the front panel (where the door is at). There may be a couple more screws to free the control panel. Take the panel off the front of the bottom (just above the pedestal if applicable). Take the screws out at the corners of the front panel (where the door is at). Open the washer door and take out the screws to free the front panel. The front panel is also hooked on brackets, so you will need to slide it up a little bit to take it off. Be careful of the rubber seal, because it will still be attacked to door (you might want someone there to help hold it). You just need enough room to get that door lock latch outta there. Remove the screws holding the door lock latch, and pull it out of there just enough were you can disconnect the wires. Connect the new door lock latch, put it back in place and then put the screws back in. Remember the brackets on the front panel. Once you get that panel back in place, continue the re-assembly. As for the door plunger, there are only 2 screws holding it on the door side. Do everything slow and carefully, and it should work out ok.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

  • Door Lock Latch

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerRobert from Dallas PA

"door locked" light always on. Washer would not run

Remove bottom kick plate of washer. Remove 4 screws behind door that hold the latch/lock assembly. Reach up inside the washer from underneath to unplug 3 wire connectors. (This is a very tight spot). Once wires are off, part comes right out. Connect wires to the new part - this is by far the most difficult part of the job because it is way up inside the washer. Replace all bolts.
Overall, pretty easy to do - just reconnecting the wires is a pain, but if you are patient it is not a big deal.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3