Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS1020949
This part works with the following brands: GE, Hotpoint & Kenmore.
This part fixes the following symptoms:
Removed covers on the freezer compartment to gain access to the evaporator fan motor.The motor was turning but not fast innoff to move air true tthe evaporator coil.The evaporator fan it is the one that will cool the bottom and top of your refrigerator.
Help other customers find the most helpful instructions.
Were these instructions helpful?
1. content of freezer was put in an ice box2. panel covering rear of freezer compartment was removed, a few screws3. old fan now accessible was removed an new fan mounted.4. modular wiring plug broke, wires had to be soldered and wrapped in heat shrunk insulation5. compartment was cleaned an rear inside panel closed Thanks for all those who shared their experience and the schematics available on website. It gave me the confidence to to this myself. Its my second repair in freezer (previous being a defective heater)
I had to remove the contents of the freezer, and remove the fan covers ( 2 screws) and the back of the freezer. I pulled out the evap motor assembly, removed the motor from that and re-installed the new motor into the assembly, (2 screws). Installed the evap assembly back into the freezer, ( another 2 screws), making sure to plug the motor into the wire harness and keeping the wires away from the fan blades. Then installed the back of the freezer (2 screws...again) and put on the 2 plastic pieces that completes the freezer assembly. I plugged the refrigerator back in and heard the fan start and knew everything was going to work fine
I pulled the inside cover in the freezer off, pulled the motor out of the bracket, replaced the fan blade , motor, and grommet and that was pretty much it. Very easy to replace. Parts select was fast and had the cheapest price available.ThanksSteven Roffey
Could not haven been easier. Simply unplug fridge, remove air duct mounted on rear panel, release panel itself, pull fan blade off, disconnect grounding wire, detach fan motor bracket, disconnect wire harness to release fan motor, install new fan motor and reconnect, secure with bracket, reconnect grounding wire, reposition fan blade onto motor shaft, reinstall rear panel and secure screws. Remount air duct and plug appliance back in. VOILA. All done in less than 15 minutes!!!
In freezer box removed shelf, removed 2 screws from back panel, removed 3 plastic covers (1 with 2 screws, other 2 snaped out. Unsnaped defrost thermostat from copper tube then cut 2 wires (yellow & orange) stripped all wires back a little then used 2 wire nuts to reconnect the new thermostat and resnapped back onto the copper tube. Removed 4 screws from evaporator fan housing (original one warped from overheat and caused fan blade to get chewed up) unpluged fan motor wiring and removed ground wire and motor from warped housing, removed fan plade by just pulling on it. Installed new fan blade by pushing it on the fan motor shaft, reinstalled the fan to the housing and the housing into the freezer box. In the frig box I removed the control panel from top of the box by removing 4 screws and unpluging the main wiring plug and the defroster control then reinstalled it all in reverse order. Also had to renew the stick on foam on the evap fan housing. Over all it was an easy task.
Removed shelf by pushing to left and lifting up on RH end. Removed screws in plastic cooling tower and slid tower up. Pulled back wall of freezer compartment out, RH side first. Removed two screws from fan bracket, unplugged fan wiring harness by compressing connector spring clips and pulling joint apart. Pulled fan blade off (note location of blade on shaft for reinstall alignment purposes), removed both green grommets.Then just reinstalled new items.My philosphy on repairs of this nature is to replace all related parts that could be contributing to problem. The parts are cheap compared to the aggravation and inconvenience of doing the repair several times until you fix the problem. You don't need to purchase the compression ring if you buy the fan blade as it has one already installed on it. Problem solved, though now that the noise is gone am hearing fainter similar noises from lower fan. Should I be surprised, both fans are of similar design.
Removed old fan and replaced the fan with new one.2 years ago, the refrigerator was under warranty and tech replaced the fan but I found that the fan was not the original spec fan. Apparently, the fan that the tech replaced did not fit opening. Now, my refrigerator works no problem. Save a ton of $$$ by doing it myself. Do not have to buy a new fridge and this one works perfect.
The original design is poor. The evaporator fan is mounted in an upright position just below the ice-maker. A plastic grate mounts over the fan assembly to allow for air circulation. Unfortunately, random chips of ice from the ice maker can fall into the fan, causing the fan to shear its blades. Replacement of the fan blade is relatively simple (accept for having to completely unload the freezer and remove all back covers, the ice-maker auger motor assembly, and the metal evaporator cover). In order to mimimze this from reoccuring, I installed a 1/4'' mesh metal screen over the exhaust ports on the cover. Thus far, this has worked well to keep ice chips out of the evaporator fan.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.