1020114-1-S-GE-WH08X10024        -Drive Belt
1020114-1-S-GE-WH08X10024        -Drive Belt

Drive Belt

PartSelect Number PS1020114

The main drive belt is designed to work with the motor pulley and spin the drum until it comes up to speed. NOTE: Per factory measures 48.4" at rest & 51.2" when working.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Pumps but will not spin.
  • Will not agitate.
  • Burning smell.
  • Noisy.
  • Shakes and moves.
  • Compare At

    $67.93
  • You Save

    $11.32
  • Your Price

    $56.61
In Stock
Order within the next 10 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 3 reviews What's this?
1-3 of 3
 

100 of 121 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers, Socket set

CustomerBRETT from CLINTON CT

Rear tub pulley became loose and deformed pulley shaft

Ordered new Parts. Removed old/worn parts. Found that the "hammering" from a loose pulley had worn and deformed the edges of the shaft where the flats are to accept new pulley.
Gently filed the flats with the flat surface of the file and filed the hump on the shaft that the "hammering" created. Take extreme caution to not file surfaces too much, because new pulley will be loose and the next step is to replace the drum shaft.($$$$) Pulley did not fit 100% (Had some slop) but that was from material being worn away from "hammering" effect. Torqued with Torque wrench and added green 609 loctite compound - this is meant to help adhere and take up some loose fit in assemblies. - Drawback to Loctite is most have to be heated to 300 to 400 degrees to remove, or pulley will need to be cut off and ruined, I further repair/removal of pulley is necessary. This is an Easy Fix/Replacement of parts.... The hard part is filing the drum shaft surfaces to accept the new pulley, and getting the belt back on - Belt is tight but needs to be stretched on like putting a bike chain back on.

Washer now spins and sounds like a dream!
- Good Luck!

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 27 people found this instruction helpful

Parts Used

  • Drive Belt

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsSocket set, Wrench(Adjustable)

CustomerBernard from Antelope CA

Driving belt worn/broken

First I unpluged electrical cord. removed the 4 screws
on the back panel. I then loosen the (1) motor bolt that
you can adjust for tightness after you put the new
drive belt on the round pulley. Make sure the bolt in the center of the round pulley is tight. The round pulley should not wabble. Make sure not to over tighten the drive belt on the motor. A slight play is fine. Put back
panel on and plug electrical cord. Run washer cycle
on and check. Should be OK.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 14 people found this instruction helpful

Parts Used

  • Drive Belt

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

Tools

CustomerSavian from Pahrump NV

Was in need of a belt

It. Was awasome the part fit great and it was even deliverd sooner than expected thank you

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-3 of 3