1019151-1-S-GE-WH13X10023        -Water Inlet Valve
1019151-1-S-GE-WH13X10023        -Water Inlet Valve 1019151-2-S-GE-WH13X10023        -Water Inlet Valve

Water Inlet Valve

PartSelect Number PS1019151

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Will not fill with water.
  • Will not stop filling with water.
  • No hot or cold water.
  • Leaking.
  • Compare At

    $70.22
  • You Save

    $11.70
  • Your Price

    $58.52
In Stock
Order within the next 12 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.4 / 5.0, 2 reviews What's this?
1-2 of 2
 

22 of 25 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Wrench(Adjustable)

CustomerRobert from Altoona PA

Machine would not fill on any cycle requiring hot water, machine would work fine on cold cycles

I Disconnected power to machine and shut off water supply lines. Move washer away from wall and removed supply lines.(good time to replace them if older than five years) Where these supply lines attach to the washer is the water valve you are replacing. There are 3 screws on the back of the cabinet lid, then on the front 3 more screws hold the lid to the plastic control housing. After removing screws you need to slide the lid up and towards the back of the machine app. 1 1/2"to 2" before you can raise the lid up and off of the machine. Once the lid is off it is just one screw holding the valve, and a hose clamp that needs removed from the end of the valve. Then slide valve to the right (looking from front of machine to the back.) I left the wires attached to the old valve,installed the new valve then reattached the wires in the same order as they were on the old valve to avoid confusion. (note valve must slide into place to get screw to line up.)assemble is reverse of the above steps. Don't forget to level machine. Be careful attaching water supply lines plastic valve threads can strip without much effort.

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 18 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerAllan from Tucson AZ

Inlets cross threaded from water hose connections

I unplugged the power cord from the wall outlet, then I had to remove the top panel off the machine by removing the three phillips screws holding the back trim strip to the front top of the machine, than I removed the three 1/4 inch head screws holding the top panel found at the back top of machine. I now pulled the top pannel to the rear and removed the top pannel. Then I used pliers to squeeze open and slide clear the small clamp to the rubber hose to the valve and removed the hose end to the valve. Then I carefully pulled off the four wire connectors to the two solenoids of the valve.
Than I removed the one 1/4 inch head screw found on the back side of the machine securing the valve to the machine. Then I removed the valve by sliding it to the mounting screw side to disengage it.
Install the valve in reverse order but I tightened the valve holding screw only till it's seated because it screws into soft plastic. 6/15/08

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-2 of 2