This part is located at the bottom of the door. It prevents water from leaking out of the dishwasher.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your General Electric Dishwasher Short Bottom Door Seal
Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Dishwasher.
This part works with the following products:
General Electric, Hotpoint.
Part# WD08X10059 replaces these:
AP3860882, 1168254
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
4.3
Filter By Rating:
5 Stars
2
4 Stars
0
3 Stars
1
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
George A - August 10, 2021
Verified Purchase
Job Little more difficult than what the video shows. seems to be working properly up to this point.
Sliding the seal onto the groove was more difficult than expected though. The part also seems expensive!!
★★★★★
★★★★★
James B - May 27, 2020
Verified Purchase
Dishwasher door seal
I think $87.00 is outrageous to charge for a short bottom door seal
★★★★★
★★★★★
Ernest S - December 28, 2018
Verified Purchase
easy fix
arrived quickly fixed quickly
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.9 / 5.0, 5 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Bottom door seal had crumbled with age
Removed inside of door, slide bottom seal on and put inside door back on. Job done!
Dorothy from LAKE WALES, FL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaking door
changed the door gasket no tools,just pulled out the old,lined up the dot (printed on gasket)on the new and started at the top pushed in the new took five minute,the short bottom door seal required a phillips head screwdriver to remove the inside door screws(six screws) the two on the bottom are different they attach to the door hinge and
... Read more are machine thread the other four are coarse thread.lifted off the panel slide off the old(pay attention to which way the curve goes) slide on the new replaced the panel put in the six screws.the job is done! the door will be tight to close but will be easier after a few uses.
Took screws out of door. Slid bottom seal off and slid new one on.
Roger from Demorest, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
10 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
seal around bottom of door leaking heavy water onto floor during use
First you must remove all screws around inside door frame, and remove panel. (I would recommend using something to weight door down after removing panel from door as it will try to continue to close) Flip panel over and remove old seal by simply pulling off, paying close attention to how the seal is fitted and direction it faces. Clean a
... Read morerea of any debris,and let the learning curve begin, after several frustrating attempts, I found it easier to install new seal by first installing it backwards by sliding seal along its track and groove, this will allow it to loosen up, then remove it and install the seal by lapping it over the the track and snapping/sliding it into place. The repair itself from the service center would of been $180.00 - $200.00, I did it myself for $39.00. I would recommend anybody with a sense of aptitude and patience to do this repair themselves. After some research I found out that this model and problem is a common repair, which is somewhat ridiculous in my opinion, as the machine itself is only 2 1/2 years old and it came pre-installed in a new home.
Read less
John from Hillsboro, OR
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
53 of 65 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door seal was never installed when machine was manufactured
removed two bottom screws on inside door panel and slid seal onto spline, reinstalled screws. Job done
John from Lakeport, AL
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
14 of 15 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tim
February 19, 2018
The image on this item does not look very wide compared to the door itself. What are the dimensions of this seal?
Hi Tim,
Thank you for your question. The dimensions of the short bottom door seal are 21 3/4 inches by 3 inches. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.