Average Repair Rating: 3.4 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Appeared the fan condensor motor had went out. Then the display seem to only work part of the time. It was the main board!
Always unplug your appliance for safety reasons first. Remove the 4 screws on the Main panel cover. It is about 6" X 8". Mine was on the left hand side as you face the BACK of the refridgerator. Follow the instructions that come with the part for your appliance. Ours has 4 plastic pop tabs, be very careful not to break these. With a pair
... Read more of pliers, squeeze the tabs together and carefully pull each corner foward. Replace the new board and put all of the plugs back in the correct places. Put the cover back on and replace the screws. Plug your appliance back in. Not a bad repair. It was just the problem of the several different issues including the refridgerator not cooling. Our freezer was still very cold and would make ice. The first thing we had was a condenser fan motor. This fan is ran by the main board. Then the display in the fridge didn't work all of the time. Finally it was not cooling properly. As we were replacing the main board, we noticed a few variances in the two. It appears to have some different transistors and some have been added. It is my opinion that this was a factory default part.
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
November 22, 2021
When the refrigerator door is opened, sometimes the temperature readout will go blank after a second and the door open beep will start without delay. Sometimes the beep will start a minute or two after the refrigerator door is closed. Sometimes everything works the way it should. The door switch is functioning properly as the light always comes on when the door is open and goes out when the door switch is pushed in. The door switch was replaced after this problem started. There is some intermittent fault in the circuitry that displays the temperature and controls the door open beep. Is this a replaceable circuit, and where is it located? Other than this the refrigerator is operating properly.
For model number PDS22MFWCBB
Hello John, Thank you for your inquiry. First make sure that the doors wiring harness is plugged in securely. Check for any visible damage. We also recommend replacing the display control board. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Stuart
November 25, 2019
Hello, the temperature display no longer illuminates and neither the fridge nor the freezer cool. I've replaced the display control board (wr55x10522), however the problem persists. The new display flashed on and off once but that's it. Any suggestions what i can try next? Thanks.
For model number PDS22MBSBWW
Hello Stuart,
Thank you for your question. Our sources suggest replacing the electronic control board for your model under part PS12069099 to fix the fridge. Hope this helps!
My refidge broke after a power outrage! i replaced the control board, and it starts to work, the problem is the temperature control is not on, all out. i can not set the temperature!
For model number PFS22SISDSS
Hi Long,
Thank you for your question. If the temperature display is out, it will need to be replaced. The part number listed under your model number for the temperature display is PS1015896. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Herby
August 7, 2019
The fridge temperature control does not stay on the desire temperature set. It stays on the ambiant temp even though you choose one and never reach the set level. It stays at 57 for example and never reach the setting. What do i do to have it work properly again. Is it a sign the temperature control is not working or other.. how much is the temperature control button?
For model number PFS22MIS
Hello Herby, thank you for inquiring. Replacing the Temperature Sensor part number PS304103 or the Electronic Board part number PS12069099 for your model will most likely fix the issue. The prices are listed in the part descriptions. I hope this helps and good luck with your repair!
Was this helpful?
Thank you for voting!
Stuart
August 22, 2019
The temperature display no longer illuminates and neither the fridge nor the freezer cool. Will replacing this part part likely fix the cooling problem?
Hi Stuart, we cannot be certain however replacing the control board is a good guess. Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
