1015640-1-S-GE-WD22X10046        -Middle Spray Arm
1015640-1-S-GE-WD22X10046        -Middle Spray Arm 1015640-2-S-GE-WD22X10046        -Middle Spray Arm

Middle Spray Arm

PartSelect Number PS1015640

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Not cleaning properly.
  • Unusual Noise.
  • Compare At

    $12.05
  • You Save

    $2.01
  • Your Price

    $10.04
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 7 reviews What's this?
1-7 of 7
 

42 of 50 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerRic from Henderson NV

Diswasher wasn't cleaning the dishs because the spray arms were clogged with calcium deposits.

Replacement of the arms is very simple, the bottom arm pulls out after turning it counter clockwise, no tool needed. The upper arms need the use of a nut driver or simlar tool to remove the hex screws holding them to the water supply tubes. The hardest part of the repair will be removing the top dish tray. This requires twisting the door slide end retainers outward to remove them and then the dish tray will slide out allowing easy removal of the arm. The top arm is mounted the body of unit.
This problem would not have occurred if there was an inline filter on the cold side to filter out calcium (whole house filter). Another way to have corrected this without the purchase of parts would be to run the dishwasher on the rinse cycle 3 or 4 times using 1 cup of lime away on each rinse and also by removing the arms and soaking the arms in a 50/50 solution of water and lime away for 24 hours. This will break down the calicum and enable the arms to be cleaned using a garden hose. New parts however save time and labor in cleaning the arms, however the main drain and supply lines to the arms still need the rinsing prior to replacing the new parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?

10 of 15 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Wrench set

CustomerTaylor from Scotia NY

Dishwasher wasn't cleaning properly

My dishwasher was doing a terrible job of cleaning. It was leaving food on dishes, and wasn't dissolving all the detergent. I replaced all the spray arms and the filter, as they seemed clogged, and god knows how old. It's a super easy repair, and the dishwasher now works as if it were brand new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerDavid from Lincoln University PA

Lower spray arm falling apart, dishes not cleaned

This was very easy. 1) roll out lower rack, 2) rotate lower arm slightly counter-clockwise and lift it out, 3) install new lower arm by dropping into position and rotating clockwise. 4) roll in lower rack, and roll out upper rack, 5) use a nut driver to remove the retaining bolt/screw from the upper arm - it's in the center of the upper arm and you have to work from underside of upper rack, 6) remover upper arm, 7) install new upper arm by holding in position and re-inserting the retaining bolt/screw. 8) Tighten the retaining screw and make sure upper arm freely rotates.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 15 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerJoel from Temple TX

The spray arm was off and without brackets

I looked at the diagram on the web site, the same one that I ordered from, and figured out how all the parts were suppose to go together. The spray arm has 2 brackets so it was a matter of aligning the tube that feeds the spray arm with the supply line on the back of he dishwasher. I had to move it once to get it properly aligned but found it to be simple.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Middle Spray Arm

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsWrench(Adjustable)

CustomerPamela from Bakersfield CA

Broken middle spray arm

Unscrewed the screw holding it in place and removed it, out the new one in place and screwed it on. Very quick and simple.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerDaniel from Maurice LA

Dishes where not clean after washing

change the nozzles and filter

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 8 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:1- 2 hours

ToolsNutdriver

Customerken from crestwood KY

Would not spray water or rotate

Took the old ones off and put the new ones in.

My water has a lot of calcium and the spray arms clog.
Second time in 3 years

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-7 of 7