http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/IAZWUPHM.gif
See part 14 in the diagram
http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/IAZWUPHM.gif

PUMP-WATER

PartSelect Number PS10067009

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not drain.
  • Noisy.
  • Pumps but will not spin.
  • Leaking.
  • Burning smell.
  • Will Not Start.
  • Compare At

    $127.02
  • You Save

    $21.17
  • Your Price

    $105.85
In Stock
Order within the next 9 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 16 reviews What's this?
1-5 of 16
 

180 of 206 people found this instruction helpful

Parts Used

  • PUMP-WATER

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerAndrew from St.Louis, MO

F 21 error

Removed the front panel unplugged
The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.

Help other customers find the most helpful instructions.

Were these instructions helpful?

45 of 49 people found this instruction helpful

Parts Used

  • PUMP-WATER

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerKurt from Caliente, NV

Water pump failed

Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.

Help other customers find the most helpful instructions.

Were these instructions helpful?

41 of 42 people found this instruction helpful

Parts Used

  • PUMP-WATER

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Wrench set

CustomerShawn from Clyde, NC

Replaced drain pump on whirlpool he duet sport washer

This do it yourself repair saved me the cost of a repair man's service call plus time to put it in. 1. First of all, make sure the unit is unplugged. On this type of front loading washer you will need to remove the bottom panel, which is secured by 3 nut screws. 2. Once the panel is removed you will need to use pliers to unscrew the drain plug and allow for excess water to drain out before removing the drain pump (get a pan or something that will fit underneath the drain). This is the area in which all the loose stuff, like coins and everything else falling out of pockets, gets trapped. The trap works well and needs to be checked periodically or if left unchecked it will probably be the cause of burning up the drain pump. 3. Once the water is drained you will need to use pliers to unsecure the two hoses attached to the drain pump. The pliers will pinch the wire clamps open and you can remove the hose easily. 4. The dryer is stacked on top of my washer and in order to get to the two screws holding the drain pump I needed to put a block of wood under the washer to give myself room to get a wrench to the screws. Once the dryer and washer were unloaded and nothing on top I was able to lift the washer and slide a block of wood underneath. 5. The pump has a power supply on the right hand side (a small white box with a wire attached) Remove the wire by gently pulling on the end of it. It is a plug type end. 6. Using a wrench (or socket driver) I took out the two screws (about an 1.5"). The drain pump slides to the right and out it comes. It is also secured by two rubber seals which are easy to remove as well as to install. 7. Now all you do is work backwards, installing the new drain pump by sliding the seals in place and wrenching the screws back in to hold the drain pump, followed by putting the two hoses back on with the pliers and placing the wire back into the power supply box on the drain. I would recommend anyone being able to do this on their own or at least with another person to help with a bit of lifting. The only way I knew to replace this part was because it was making all the noise, so it doesn't take much rocket science :)

Help other customers find the most helpful instructions.

Were these instructions helpful?

26 of 31 people found this instruction helpful

Parts Used

  • PUMP-WATER

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsPliers, Socket set

CustomerAmy from Phoenix, AZ

Water wasnt draining from tub/digital error msg

Took drain pump out and determined coins and practice ammunition are not good for drain pump rhesevior. Drain pump burnt up and froze. Part was easy to slide out and slide back in hooking up two hoses to it. Five minute fix!! Now we know where those rouge items went. Lol

Help other customers find the most helpful instructions.

Were these instructions helpful?

15 of 20 people found this instruction helpful

Parts Used

  • PUMP-WATER

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerHong from Flushing, NY

Water leak under machine caused by cracked drain pump

Turn of the electrical power to the machine. I took off the cover on the machine below the door. You had to use phillips screwdriver to get the three screws out. In order to replace the pump I had to lift the washing machine about three inches up slightly over to one side (needed a strong person to lift as there was a dryer on top of it). The old pump has to be removed with a nutdriver as there are two nuts holding the pump in place under the machine ( I had to run out to the hardware store to buy a smaller one to fit under the machine as the big wrench was to big to fit under the machine). I unplugged the electrical connection to the pump. I unclamped the hoses attached to the pump using a plier, make sure you have something to hold water that will drain from the hose. I then push/pull the old pump to the right out of its place, it is attached to the metal at the bottom of the machine. I put in the new pump and tighten the screws on the bottom (this is the tricky part as you cannot see - a mirror may help). I also reattached the hoses and electrical connection. I turned on the machine to rinse to make sure there were no leaks before putting back the cover. Before throwing out the old pump, you can shake it and look in the opening of the old pump for any valuables left in pockets that may have washed out. I found a 18k bracelet, 25 cents and a small screw which may have caused the hole in the pump . Good luck :)

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 16