This part is the replacement belt install tool for your dryer. It comes with two round plastic halves of the tool that are held together with an o-ring (also included). To use the tool, position the two halves of the tool together, and roll the o-ring into the groove to secure. The belt install tool will allow you to replace a damaged drive belt on your dryer. Be sure to disconnect power to the dryer before you begin this repair. This is an OEM part sourced directly from the manufacturer.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Will not agitate
This part works with the following products:
Washer.
This part works with the following products:
General Electric, Hotpoint.
Part# WX05X20641 replaces these:
AP5957260, WX05X10102
Customer Reviews
Average Rating:
★★★★★
★★★★★
3 Reviews
4.3
Filter By Rating:
5 Stars
2
4 Stars
0
3 Stars
1
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Connie Y - October 31, 2020
Verified Purchase
Necessary for driver belt installation
It is impossible to install a driver belt into your washing machine without this little tool and a zip tie. If you need to replace your driver belt, you absolutely need this.
★★★★★
★★★★★
Dave D - December 30, 2018
Verified Purchase
Quick & easy tool to use.
Part came as described. Used directions included along with tool. Belt went on easily.
★★★★★
★★★★★
Rick K - March 9, 2018
Verified Purchase
The belt repair tool worked just as it was designed to do.
The repair tool worked fine and it is probably necessary to walk the new belt onto the pulley and drive shaft. I think it was way over-priced. A simple O ring and 2 small cast plastic pieces. The belt I replaced had lasted about 20 years. I won't live long enough to get my "money's worth."
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 6 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The washer belt started slipping - this is not a hard DIY
The video on this site was very good and simple compared to others so if you are replacing a belt please follow the directions given here. A few comments: * when you compare the new belt to the old do not panic - the old belt is much larger which would explain the slipping. * get the belt installation tool - it is worth it
... Read more/>* use three tie wraps instead of one. I never got a single one tight enough to hold the belt. using three it went straight on. * as in the video, move the belt around to the right once the tie wraps are in place * once you start to move the belt onto the drum pulley be sure the belt is hanging below the pulley and it is clear of the motor mounting brackets. There is not enough clearance if the belt rest on top of the pulley as you move it around. The motor mounting bracket seems to want to catch the belt and you run the risk of cutting the belt.
It took me less than 45 minutes with my learning curve so the next one will take less than 25.
Read less
James from KATY, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad timer and belt
Removed screws from the back removed screw from timer replaced timer. Removed front panel and replaced belt videos were extremely helpful
I happen to be a mechanic so the repair was quick and saved me from buying a new washer! But the step by step videos yhat come with your parts are very easy to understand . This company has saved me thousands of dollars on new units or calling a repair company
The repair would have gone well, however partselect sent me the wrong part. Instead of a washer belt, they sent me a door seal to what looks like a refrigerator
I am so glad I bought the belt installation tool. I tried black ties several times to hold belt slack and kept breaking. I used two stainless steel hose clamps purchased at a local auto parts store. They held the super tight belt to the pulley to be able to install belt with purchased tool to get the belt on motor pulley. Washer is workin
... Read moreg again.
Washer makes loud whining noise, intermittently, during spin cycle.
The "service kit belt tool" was difficult to install, but I oonsider it a necessity. We tried installing the belt without the tool, and the belt kept snapping off the motor drive pulley. Using a cable tie to hold the belt to the drum pulley did not work. I used a length of heavy duty duct tape instead, and that worked OK. Unfortunately, t
... Read morehe whining noise is still present with the new belt, so a GE service technician visit has been scheduled. Our belt replacement effort has not been totally wasted, unless the washer can't be repaired economically, since the old belt was fraying.
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Neal
October 18, 2017
There is a growling noise, a bearing i am sure. It appears the bearing or bearings come with the shaft and mode selector assembly. The bearing noise is audible any time the washer is washing and worse when in the spin cycle. I would assume this is a common failure after 12 years. Is it possible to replace just the bearings is my second question? I don't see any bearings listed separately. Please help.
For model number WWDRR418G0WW
Hi Neal,
Thank you for your question. Yes, your bearing does come separately. I have listed it in a link below for you. Good luck with your repair.
Picked up the washer myself, laid it down in the truck. Afterward, the tub was imbalanced and make lots of noise. Washes fine, but noisy. Should belt be replaced or put back.
For model number HSWP1000M3WW
Hello Martha, thank you for inquiring. For this symptom you will want to consider either the Tub Dampening Strap part PS271100, the 6-Rib Drive Belt part PS1482278, or the Tub Bearing Washer part PS271509 for your model. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
