Emitter and Receiver Boards

PartSelect Number PS10064583

These boards tells the icemaker when it's full and that it has to dump the ice, and it also tells the icemaker when to refill with water.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Ice maker won’t dispense ice.
  • Ice maker dispenses too much ice.
  • Compare At

    $205.20
  • You Save

    $34.20
  • Your Price

    $171.00
In Stock
Order within the next 6 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 69 reviews What's this?
 

0 of 1 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Wrench set

CustomerErnest from Reno NV

Ice maker stopped working

I first ordered the electronic control boards. However, they arrived with an Instruction Sheet. The diagnostic procedures listed on that sheet identified that the optics were working properly, so did not use the electronics. That left the motor assembly as the culprit. Ordered that. The motor assembly arrived promptly and installed easily - just like the video. Ice maker began making ice immediately. Thank you PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerRick from Lorain OH

The icemaker would not work

I tried several things first : changed the filter cartridge, then the water control valve, then the control boards but still no ice. Rather than buy a new motor assembly, I bought a whole new icemaker which included the motor assembly and finally SUCCESS! In total it cost me about $350 but you have to try the easier and cheaper things first. One 1/4" screw and disconnecting the wire harness clip plus reusing the old icemaker base and the repair was complete. I would recommend a more detailed discussion on what each part does and the way the colored wires attach. Wire clips can sometimes be connected upside down. I was very happy with how quickly I received the new part. I whole-heartedly recommend PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 4 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerEl Ray from San Jose CA

Ice maker not working

After checking the codes, they indicated that the emmitter board was inoperative so I changed the control boards. Very simple and straight forward (about 10 minutes). After changing the boards I double checked the codes, this time the codes indicated the control boards were functioning properly but still no ice. A friend suggested the water feed line could be frozen and defrosting the freezer could possibly resolve the problem. My freezer is full and it will take time to empty it to continue. Any other suggestions in the meantime? Installing the new water filter took about a minute and is working properly.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerPAUL from FAIR LAWN NJ

Ice maker stopped working

I paid for a service call to have the problem diagnosed, and then ordered and changed the parts myself, saving about 50% off the original estimate.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerDavid from Davis CA

Ice maker stopped working

After calling Sears and setting up an appointment and waiting 7 hours for them not to show.. without any phone call..even after the dispatcher said I was "Next on the List" I figured thilure was the Emitter boards.. I ordered theere had to be a better way.. I researched this site and determined that the most likely cause of fa parts and received them within 3 days with standard shipping. I followed the optical diagnostic instructions that were included and replaced the boards. Within a few hours the ice maker was singing again.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerWilliam from Margate FL

Sensor board on icemaker

First I removed the icemaker and the sensor boards by removing 6/7 screws. Next, I placed the new sensors into the emitter and receiver and re-installed the components...reset the icemaker and was all done!

Last time my icemaker broke I paid a contractor $225! This time I did it myself in 30 minutes and saved $150. And it was so easy my wife could'a done it......

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerTerry from Avondale AZ

Ice maker was not producing ice.

I removed the receiver cover and replaced the board (three screws, two on the board) did the exact same procedure on the emitter board ( three on the cover, one on the board). This process took all of 4 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMark from Georgetown TX

Ice maker would not stop making ice.

Unplugged electrical cord for refrigerator, Removed the 3-screws for the bad Emitter, unplugged the wiring harness, plugged the wiring harness into the new Emitter put into position replaced screws, Removed screws for bad Receiver unplugged wiring harness, plugged in new receiver put into position replaced screws plugged refrigerator electrical cord back in. Working ok.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerStephen from Chicago IL

No ice was being made

After reading other repair stories online, i ordered the parts, followed the included instructions to replace the boards and the next day i had a full bin of ice. This is the second refrigerator i fixed with parts from partsselect.com. They are AWESOME!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJuan from Tomball TX

Ice maker wouldn't stop making ice then quit 1.5 days later

removed 3 screws on each side of freezer where the ice maker controls are unplugged the circuit boards. un screwed the boards from the plastic and put the new ones in, reinstalled. now, Ice and not over flowing! :)

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerDavid from Ennis TX

No ice no movement in ice maker

Being 50 miles from the Sears with a 7 year old unit, I actually changed out both board (a kit) which was 9 screws. 3 screws in the outside panels, and 2 in the larger board, and 1 on the smaller board. Both both boards plug in. I also changed the actual ice maker which unplugs and slides out on my unit. Remove a single screw (1/4") on bottom to remove a plastic shield that covers/protects the plug in. A plastic arm lock is in the bottom guide tray, push it up first. Then unplug the unit. Three more 1/4" screws in bottom to remove the custom plastic mount. Then reverses the process to install the new ice maker. Total $175 plus 1 hour labor. In 6 months the unit will have paid for the repairs. I hope to get 5 years of service from the job

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerTJ from Jasper GA

Ice maker wouldn't fill with water to make ice.

Removed the screws and disconnected the part from the base. Attached the new part to the base and screwed back in. No big deal!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerJudy from Baufort SC

Ice maker stopped working

the repair went fine but the ice maker still is not working is there something i am missing

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerCharles from Chino Hills CA

Quit making ice

I watched the video on your web site and did exactly what the video showed. I could not a get an appliance parts shop to tell me how to test the sensor, so I went on your site. It not only showed me how to change the sensor,it showed me how to test the sensor in my refrigerator. I have changed ice makers before, but never the sensor. Your site saved me $75 dollar service call and saved me $35 dollars on the part. Thank you very much!!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Emitter and Receiver Boards

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerEdwin from HEMET CA

Ice maker stopped working

Removed and replaced ecbs as shown invideo. However cannot seem to force harvest cycle. Meter probe of H & T do not seem to make contact with any contacts. Help!!

Help other customers find the most helpful instructions.

Were these instructions helpful?