http://www.partselect.com/Schematics/Whirlpool/Whirlpool_Thumb/RGYMB1A8.gif
See part 1 in the diagram

Control Panel and Touchpad Assembly

PartSelect Number PS10064581

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not start.
  • Compare At

    $149.27
  • You Save

    $24.88
  • Your Price

    $124.39
On Order
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 6 reviews What's this?
1-6 of 6
 

24 of 27 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerPeter from Colleyville TX

Control panel buttons were worn out, circuit board shorted out

Turned off the power at the breaker; took the screws out of the door panel; the control panel was already loose; I took the lock mechanism off the panel, and then removed the electric bundle panel from the control panel; the only thing left was the cicuit board, which I removed, and the wires to it were in a clip all together; I clipped the wires to the new cicuit board, replaced it in the panel slot, then clipped in the wire bundle; the lock mechanism fit right where it was supposed to, then I replaced all the screws in the door panel , starting at the top where the control panel was; I turned the power back on, then turned on the dishwasher- it worked just like new. This was a fairly easy fix for about $150; that would have been the service charge and time alone for a repairman, not including the marked up price of the parts. PartSelect was a lifesaver.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 6 people found this instruction helpful

Parts Used

  • Control Panel and Touchpad Assembly

Level of DifficultyReally easy

Time to do repair:1- 2 hours

Tools

CustomerEdward from Westminster CO

The "normal" button cover cracked allowing water to seep in and damage the switch

Unplug the dishwasher. Remove the screws holding the stainless lining to the outer door panel. Unplug the various connections. remove the control panel by pushing small plastic cleats outward (they are spring loaded). Remove the printed circuit board by pushing one holding tab to realase then tilting the board out. Remove the ribbon cable by sliding it off the circuit board. Now reverse the process. Attach the ribbon cable to new circuit board, snap in the circuit board to the control panel (ribbon behind), reattach all electrical connectors, reassemble the door "sandwich". Somewhere in there you also need to remove then snap back the door lock assembly. This is a simple repair with no fancy connectors or tools. Repair service wanted $400 plus two service calls (one to diagnose, one to install). My total about $120. I am a klutz re: repairs.

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerLynn from Leo IN

Control selection pad not functioning

1st important: Make sure to turn off electricity from the dishwasher I did this from my circuit breaker to insure safety. Removed the front panel of the dishwasher, disconnected the control panel & the Electronic Control Board. Removed the 2 items. The parts arrived very promptly as promised, connectected the wires & installed. As long as someone is mechanically inclined & savy with electronics shouldn't run into any problems. Dishwasher now working as good as new. Saved significantly, previously priced out repairman & parts would have been more then double the costs incurred & saved $1000.00 if I would have purchased a new dishwasher of equal value.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

  • Control Panel and Touchpad Assembly

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerDavid from Windermere FL

Controlpanel buttons and circuit board were damaged

loosened screws, slid out black panel, removed (unclipped) 2 electronic panels and placed them in new panel. Unplugged, removed and replaced circuit board. Plugged in new circuit board. Slid panel back into position and fastened screws.
Now it as good as new...

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerFrank from Hummelstown PA

Control panel buttons were worn out

Replaced the plastic control panel- need to remove the PCB's which can be tricky not to damage them

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Control Panel and Touchpad Assembly

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerWilliam from Great Neck NY

Broken control panel buttons

I looked it up on youtube and also saw the written explanation on Parts Select

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6