Electronic Control Board

PartSelect Number PS10064575

This board comes with the metallic shield.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Will Not Start.
  • Compare At

    $388.03
  • You Save

    $64.67
  • Your Price

    $323.36
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.9 / 5.0, 5 reviews What's this?
1-5 of 5
 

9 of 12 people found this instruction helpful

Parts Used

  • Electronic Control Board

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerEdmund from Fords NJ

Many misc. Electrical issues

After removing the protective panel from the back, I used one of those screw holes to hold the new mother board right next to the existing one. I unplugged one connection & and plugged in to the new board. A couple of the wires didn't reach, but I committed those to memory. It looks a lot more intimadating than it is. It looks like a bunch of spaghetti, but its easier than it looks and it saved me at least $750

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 13 people found this instruction helpful

Parts Used

  • Electronic Control Board

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver

CustomerElaine from Jacksonville FL

My oven would either turn off or on by itself

I deduced that it had to be a major computer part and when I e-mail parts select, they concurred. I got the part and had my repair guys come install it. It did not work when he finished after three hours. after another mother board was sent a friend carefully installed it with me recording the lineup of the wires and calling them out to him. when he took the other board off he found a bad port, that did not fit well. it is now working beautifully and I got to bake all my cookies and bars for the holidays! Thank you Parts select for you help and your forum! couldn't have done it without you!

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 3 people found this instruction helpful

Parts Used

  • Electronic Control Board

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerArnold from Augusta GA

Oven wouldn't heat in any mode

Turn breaker off and start replaceing wires one at a time until you have the new part wired. Then secure new part and turn the breaker back on and it'll work. It's just that simple.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

  • Electronic Control Board

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerIla from Carthage NC

Oven would not heat

I cut off the electricity. Removed the back panel. Moved 1 wire at a time from old board to new board. Then removed the old board and replaced the new one. Reattached the back panel and turned on the electricity. I was happy when the oven began to heat.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Electronic Control Board

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJoseph from Coopersburg PA

Tomato soup

There are days when the distraction levels are higher than others; lets say you leave tomato soup on High, it boils over and runs down the sides and back of your stove. When it makes contact with ANY electrical part it DOES short out, the electrical connection can actually catch on fire. To top it all off It becomes a thick paste that is only removed by scraping and scrubbing. Double check to make sure it is out of the electrical connection block before plugging the unit back in or it'll short out again, possibly starting yet another fire. This control board has one screw and a couple wires, remove the old toasted board, install the new one and pull and move one wire at a time from the old to the new board.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5