http://www.partselect.com/Schematics/GE/GE_Thumb/00116398i02.gif
See part 610 in the diagram
http://www.partselect.com/Schematics/GE/GE_Thumb/00116398i02.gif

MOTOR AC/DC EVAP FAN

PartSelect Number PS10063450

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Noisy.
  • Fridge too warm.
  • Freezer section too warm.
  • Will Not Start.
  • Compare At

    $44.48
  • You Save

    $7.41
  • Your Price

    $37.07
In Stock
Order within the next 3 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 23 reviews What's this?
1-5 of 23
 

123 of 130 people found this instruction helpful

Parts Used

  • MOTOR AC/DC EVAP FAN

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerLuis from College Station, TX

Freezer fan

I removed two srews from the back panel inside fthe reezer compartment and the two that hold the air manifold/baffle? and pulled the baffle out. Then, I removed the two srews that hold the front part of the fan bracket behind the baffle and the back panel came out easily. Two more screws and one quick connect plug attached to the fan and I was done with removal. Insallation was even quicker, I slid the original fan right off the old motor and slid it on the new motor's shaft. Piece of cake! Thanks Partselect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

47 of 51 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set, Wrench (Adjustable)

Customeralex from rohnert park, CA

Evaporator fan making lots of noise

the repair was really easy!!! took longer to put the little clip on the fan part than it was to install the whole moter and put everthing back together

save money do it yourself.....

Help other customers find the most helpful instructions.

Were these instructions helpful?

19 of 19 people found this instruction helpful

Parts Used

  • MOTOR AC/DC EVAP FAN

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerArthur from East Meadow, NY

Loud fan motor

Unplug refrigerator.Remove the floor of the freezer box by removing the 4 philips head screws. Remove the cover over the fan by pulling it straight up and out. Remove the styrafoam duct by pulling it straight up and out. Remove the back wall of the freezer by removing the 4 philips head screws. Unplug fan. Remove the fan, bracket and all, by removing the two philips head screws on the back wall. Take the two halves of the bracket appart by removing the two hex head scews on the back of the bracket. Remove the "O" ring from the fan blade and remove the blade. There is a rubber grommet on both the front and back halves of the bracket. Make sure they are set properly in the brackets to secure and position the motor properly so the fan blade doesn't hit anything when it spins. Install the new motor onto the bracket the same way you took the old one off. Check the positions of the brackets, rubber grommets and motor to make sure they're properly installed and secure. Replace the "O" ring onto the fan blade and install it onto the new motor with a firm push on the center of the blade. Install the brackets and fan onto the back wall and plug in the new motor. Reinstall the back wall of the freezer box and make sure the motor is secure. Plug the refrigerator back in and check to make sure the fan blade doesn't hit anything while it's turning. Finish reassembling the freezer box.

Help other customers find the most helpful instructions.

Were these instructions helpful?

16 of 19 people found this instruction helpful

Parts Used

  • MOTOR AC/DC EVAP FAN

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerLucinda from Yucca, AZ

The lower half of the refrigerator was not cold, the fan was not blowing

First I removed the 4 screws in the back of the freezer. I then pulled the connection from the fan , I replaced the fan to the connection, replaced the 4 screws and I was done! I still can't believe how simple it was.

Help other customers find the most helpful instructions.

Were these instructions helpful?

11 of 12 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRichard from Port st Lucie, FL

Noise fan

Took off the back panel 4 screws, 2 screws on fan motar ,unpluged fan and replaced fan motor ,Hardest part of the whole job was setting the fan blade ,easy to push on but becarefull not to push it on to far.check distance on old fan before you take the blade off.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 23