http://www.partselect.com/Schematics/GE/GE_Thumb/00115410i02.gif
See part 252 in the diagram
http://www.partselect.com/Schematics/GE/GE_Thumb/00115410i02.gif

SENSOR ASM

PartSelect Number PS10059162

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Oven is too hot.
  • Oven not heating evenly.
  • Will Not Start.
  • Little to no heat when broiling.
  • Compare At

    $14.96
  • You Save

    $2.49
  • Your Price

    $12.47
In Stock
Order within the next 4 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.6 / 5.0, 10 reviews What's this?
1-5 of 10
 

54 of 72 people found this instruction helpful

Parts Used

  • SENSOR ASM

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerPeter from stamford, CT

Oven would go in to a f2 error

Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.

Help other customers find the most helpful instructions.

Were these instructions helpful?

23 of 28 people found this instruction helpful

Parts Used

  • SENSOR ASM

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerGerald from Cape Canaveral, FL

Oven wouldn't preheat above 300 degrees

Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

14 of 16 people found this instruction helpful

Parts Used

  • SENSOR ASM

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsScrew drivers, Socket set, Wrench (Adjustable), Wrench set

CustomerChad from Bloomington, IN

I kept getting an f2 error and the temperature did not seem accurate

1) pull out the stove
2) remove the 7 sheet metal screws holding the back panel on. (the panel that also covers where the cord splits and connects to the oven.
3) Find the small plastic connector located in the middle of the back of the range and unplug it.
4) open the front of the oven and remove the one screw holding in the oven temp sensor.
5) replace the sensor and make sure to "feed" the new cord through as best you can.
6) I had to dig through the insulation a little bit to find the new wiring harness
7) connect the wiring harness and put the back of the range back on

note: this was very simple to do if you think this might be the problem don't hesitate to handle this one yourself.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 15 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver

CustomerTammy from Emmitsburg, MD

Oven won't get hot, would preheat only -element don't even get hot- only the brioil element got hot.

Repair: unscrewed the back panel- 2 screw and the sensor and bake element from the inside had 2 screws each. Just stuck them through their old hole from inside to the outside, pushed plug back together. Then screwed back into place, screwed back plate back on. Plugged stove in, turned on the oven and within 2 seconds the bake element was blood red and temp. was up to 350 in less then 10 min. Come to find out only needed the oven sensor -$10.00part but I already ordered the bake element so I went a head and replaced it - cost $50.00. Have a great oven again for less then $70.00repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?

8 of 10 people found this instruction helpful

Parts Used

  • SENSOR ASM

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerLee from Greenfield, IN

Oven overheating upto 200 degrees!!

Replaced temperature sensor in the oven first ($10 part, always start with least expensive possibility!), but that didn't solve the problem. 5-10 minute repair, not counting moving the range in and out of it's home between cabinets. Next replaced the control board ($90 part) which solved the overheating problem. 15 to 30 minute repair, don't be intimidated by all the wires. Remember to turn off power at the breaker (duh). Order the faceplate graphic ($37 part) because chances are the old one won't peel off cleanly (ours didn't, "I was really careful Honey!!) and the otherwise excellent PartSelect.com website doesn't suggest the part might be needed. Anyway, I saved a minimum of $80 plus Labor by doing it myself. I had the advantage of living about 100 miles from their warehouse and got NEXT DAY delivery from FedEx instead of 3-5 business days. Suggest you order before noon.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 10