ZSGW420DMB General Electric Refrigerator - Instructions

opened the access door. It took some tugging to get the old bulb out, and is was awkward getting the prongs on the replacement bulb lined up and pushed in, but it was accomplished in about 10 minutes. You had exactly the right information on a change in the part number that was made by GE, and you shipped the correct bulb the same day I ordered it.Good job. N R Brown

When I clicked on the part to see it's description the pop up window included a youtube video on how to install the part. The video was right on the mark. Very easy installation. Phillips screwdriver was the only tool needed. Repair performed in less than 15 minutes. I have used this site before and it has been extremely helpful in saving me money by doing the repairs myself instead of paying an arm and a leg for a repairman to do it.

Removed the cover installed parts. Parts were very simple cover was a major problem. Instructions stated "simply remove cover by pushing on cover and clips will release" They dont and cover broke.

I ordered 3 temperature Sensors Part#PS304103 and viewed the video. Got there, opened the frig. and it looked totally different and no place in any part of this frig. that took these sensors as viewed on the video. Totally baffled why these parts were listed for this frig. there was no place in this frig that would access for these parts. Serial # was HR443071.Maybe this model is out of date for these parts. Trying to find someone who can repair it. Any ideas???Purchased this GE in 2008. Model #is GSS25WSTFSS Thanks, for your help. JIM

No big deal. Tiny space to work in. Patience. Patience

We received the part just a few days after ordering, unscrewed the old filter by hand, and installed the new filter the same way.

Little difficult getting the switch out, had to pry wth some force. New installation was real easy.

Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.

Removed water filter and inserted plug (works great and water flow increased)

Removed the dispenser panel and replaced-less than 10 min and a savings of $300.00 for a service call.

took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.

I started at the compressor and replaced the overload and the Ptcr first and that did not make the compressor start running again, so I replaced the capasitor and it still did not start, so I bit the bulett and replaced the Main Control Board and that is what I should have checked first, when I removed the old one I found a little burnt spot on the back that I could not see from the front. The new one did not look exactly like the old one, it had two more wire terminals than the old one, but just leave them blank and everything will work just fine!

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

as per video

My refrigerator was making a high pitched kind of howling noise. The PartSelect symptom that was closest was “unusual noise” and when I clicked that it said the evaporator fan motor fixes the symptom 32% of the time. Since my freezer fan speed sounded like it was constantly changing I went ahead and bought one which PartSelect delivered promptly. The installation video was great and although my freezer was not identical to the one in the video, the video was still very helpful. The only thing it didn’t say was how to tell if my freezer motor was the one with the thermistor although I suspect that they all are and that PartSelect is simply trying to save us money by showing us how to splice in a motor without a thermistor. Anyway, since I would have had to disassemble the freezer before buying the part to find out for sure, I just bought the one without the thermistor. This just meant I had to splice the new motor in, just like in the video. I think I would have preferred buying the motor with the thermistor even though it was more expensive. In the end my problem is solved so I’m happy. This is the third time that I’ve had to repair this GE refrigerator and PartSelect has been a valuable resource each time.