ZSGS420DMCSS General Electric Refrigerator - Instructions

Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the interior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!

I just unscrewed filter and screwed in filter bypass

none required

Removed front display and solenoid 3 screws and replace. Clean and install

Followed the video instructions with the help of a young man who worked on trailer hitches before and knew how to splice wires. Beware of splicing the wrong fan motor back into the assembly. . . . That happened here and we had to start the splicing all over again with the correct fan motor.

Pull fridge away from wall and unplug it! Turn water valve off. Open freezer door and stuff a small rag/washcloth in hole where ice exits to keep the cold air in. There are 3 small holes on the bottom of the control panel, stick a small Phillips head screwdriver in the 2 outside holes and pop the control panel out. Pull the 3 connectors out of the back of the control panel. Set the control panel aside. Unscrew 4 Phillips head screws holding the plastic control panel bracket/ice cup/light bulb. Set this piece aside. Unscrew 3 screws that hold solenoid. Mine was completely rusted. Throw the old solenoid in the garbage. All the screws I removed were rusted. Go to home depot get some stainless steel screws that are the same size as the rusted screws and some spray rust inhibitor for metal and a tube of anti-seize. Wipe everything down with 1/10 solution of Clorox/water(q-tips help to get the tight areas)to get rid of all the MOLD. Spray a light coat of rust inhibitor on your new solenoid and let it dry. Coat the metal plunger of your new solenoid with anti- seize lubricant. Replace solenoid and all other screws that are rusted with stainless steel screws. Put the plastic bracket back in with 4 screws. Plug the 3 control panel wires back in and pop the control panel in the bracket. Pull the rag out of the ice chute, turn water back on, plug fridge in and push it back against the wall. Your done and hopefully the extra steps will help your solenoid last longer! Hope this helps!

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

Slip the front cover off by gently pulling down, carefully un-plug the wire connectors (x3), remove 4 screws and remove paddle assembly. 2 screws hold the flap on and 3 hold the solenoid. Replace the screws with stainless so they won't rust. I tried coating the solenoid in lithum grease to prevent rust, onlt time will tell if it works.

I just follow to the video and take step by step. It's was very helpful and easy. Thank you.

Removed the Control Panel and the outside of the Dispenser Outlet. Removed the Flapper Door and the solenoid. Replaced both parts with new parts, and re-assembled. The pin, at the top of the Solenoid was badly worn and the plastic arm was very rough on the surface adjacent to the worn pin.

I followed the video provided by PartSelect, very helpful. I had to cut and splice 4 wires. The repair was successful. The replacement part was an exact duplicate of the original. I still notice the same sound but one tenth the volume. I hope the problem does not return. Many thanks to PartSelect for information to identify the problem and prompt shipping of the repair part.

Removed control panel by inserting small screwdriver in the 3 holes underneath to loosen. Remove 4 screws holding circuit board . Unplugged 3 connectors. Removing circuit board gave access to flapper. Removed flapper by unclipping. Installed new flapper and reversed disassembly procedure. This was 2nd time in 2 years I had to replace this part.

Had to remove all the covers and fans to expose the condenser, which was difficult as the parts were frozen to it. The styrofoam covering the condenser made it almost impossible to defrost it. Therefore, I ripped the styrofoam off to expose the condenser. Was not really difficult to fix the styrofoam cover using metal tape. Replaced temperature sensor in aluminum block, and used butyl sealant to secure. Had to also re-install parts of ice-ball kit that were not well covered. Lots of parts to keep track of, but anyone could do it.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

My 14 year old Son