ZSGB420DMC General Electric Refrigerator - Instructions

I followed a video supplied with the e-mail notification of the shipment of the part. This was one of the best experiences I have had with locating, purchasing and installing a replacement part for an appliance.

I watched the how to video and followed the instructions. The entire repair took less than 4 minutes. Hardest thing was disconnecting the control panel.

I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.

Located temperature sensor on condenser in the freezer section( as per instructional video ). Cut off bad sensor with wire cutter then soldered on the new sensor and sealed with electrical shrink wrap.

Took the paper clip, pressed in through the holes on the bottom of the ice dispenser panel. Removed the four screws. Loosened the panel and removed the wires. replaced the flapper door. Then reversed the process. Your video was VERY helpful except for the paper clip. Had to get that off another web site.

Not only was your parts selection very easy to understand,
The Video shows exactly how to install that part.
This was So Easy to repair. I thought I would have to take
the door apart from the inside but the repair was completed
with the door closed and took about 10 to 15 min. to complete.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

I followed the directions on the video. Although my dispenser was a little different, I was able to get to the faulty door in less than five minutes.

Folowed instructions

I followed the instructions on the video presentation, stopping the video each time until I had completed the described step. Only one minor change from the video...my refrigerator door (stainless steel) does not have the plastic edging around the control panel as shown in the video. It took me a minute or two to figure out that I had to push the tabs on the bottom of the control panel. The rest was easy.

I had it done with in 5 minutes,took front panel off,unpluged wires,laid panel aside took 4 screws out light fixture is in this panel,removed 4 wires,pushed fixture out of front,installed new bulb,hooked wires back replaced 2 front panels,every thing works ok now,get spare bulb if you ever need to do this again. HM

I followed the video instructions (very helpful) and used others comments for removing the control panel. For the latter I used a small allen wrench to carefully wedge the bottom two indents (look from below panel edge) slightly up and forward to release the panel. Next, after removing the four screws, the assembly (housing shield) removed fairly easily. I then had full access to the flapper and removed this carefully with the pliers so as not to damage the piece it was attached to (Dispenser Door Recess Crank?). The rubber outer flange on the otherwise plastic flapper was very irregular for approx. 1/4 of the circumference and thus did not seal. So far it's been one week and no more frost build up or frozen water dispenser line.

The Ice flapper was warped therefore, it was not closing well. Because of this, the ice dispenser got air in it and the ice cubes would deice causing to make a chunk of ice inside.I went on line, order the part ($5.75 + tax= $12.00) checked Part Select video and did it myself. It really is as seen on the video. It took me less than 10 minutes! I saved $200.00

I followed the directional video on "PartSelect" website. The video was very easy to follow and showed exactly how to easily replace the dispenser door solenoid assembly. I knew it was the solonoid assembly because the I could see the plunger that controls the opening/closing motion of the dispenser door sticking inside the old solenoid. The "PartSelect" website is very user friendly and very easy to use. The part ordered, delivered by standard delivery, arrived the day after it was ordered. I only wish all repairs could be as straight forward and easy as this one, thanks to "PartSelect" and some limited mechanical/electrical knowledge on my part. This was absolutely a "do it yourself" repair at a very significant savings over using an appliance repair service.

I followed the Video on your website and that made it so easy and simple to follow. Thank you!