ZISW480DRI General Electric Refrigerator - Instructions

Very easy, unscrew and re-screw new filter in..

I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!

I found out that the tabs that hold the ext. had broken or worn off. I decided to pull the front panel off and remove the filler spout assy. I just glued the new funnel ext. onto the funnel, and caulker the panel,and hopefully I will never need to replace it again. It will be a little more difficult to get it off now. Also, the instructions were so small I had to read it with a magnifying glass.

Removed rear cover at the bottom. Turn off water supply. Disconnect dual water inlet control and replicated it with the new one. reinstalled rear cover and turned the water supply. back on. That's it.h

I have a GE Profile French door refrig. It's only about 4 yrs old and the defroster stopped working. I read the other repair stories and was able to narrow it down to either the temp sensor, defrost timer, or main board. The refrig section was up to about 47 degrees and freezer was around 25. I could tell it was trying to cool but couldn't. So I tried the temp sensor first. I cut and spliced the new sensor on the outlet of the Evap. Coil and it took about 15 mins. Turned refrig back on and waited. The coil started to ice over after about 5 hrs I left the back panel off so I could see if and when then heater kicked on. After about 8 hrs I looked in and saw a faint glow and water trickling down and running out the drain. Turned out the sensor was bad and wasn't telling the main board it needed to defrost. I would try the sensor if you are having the same issues before spending a lot of money on the main board, defrost heater and or timer.

Went well. Changed the Ice Maker and then the Water Valve. All good and it is making ice.

It was amazing , i didn't know how to repair , i had. Insurance from choice home warranty but they say it is not covered , i was upset with them . But i get partselect .com . It is very easy, i tell my problem they tell what parts i need and also saw me video how to install it , i just did with a screw driver in 15 minutes . It was wonderful experience and a lot lot easy then what i thought. Thanks to partselect team and webside.

There were only 3parts listed to check omed out the defrost heater and thermostat ....thermistor checked bad ordered replacement took less than 2 minutes to replace after I defrosted it again runs fine

Adding a small amount of water to the filter would resolve the problem for a week or two. So, I thought this was an issue with the filter and decided to try the bypass cap to help zero in on the problem. The bypass cap had no instructions concerning the need for O ring so it was trial and error. The O ring was not needed. After installation of the bypass cap, no water flow resulted and I had to replace the filter. Intermittent problem continues.

Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.

Ironically I did this today, as this email request came up asking how it went. I'm not a repairman, I'm a software engineer, and I can't thank this site enough for the step by step videos. With the video to help, this was a breeze, I was nervous as I had to empty all my freezer out onto the living room floor. Once that was done the repair took about 30 minutes. Thank you partselect!!!!! My second time doing business here, and I'll be coming back (well, if something breaks, so let's hope I don't have to).

I watched the Video on partselect website for replacing the Solenoid. The repair went smooth. No problem.

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

Had a water leak on that valve for probably the last 7 or 8 years. Only noticed it when I had a huge water issue with a leaky faucet. Repaired that, went to repair the Sheetrock behind refrigerator and saw water in the tray under frige. Wiggle hose and realized that the reason the water on the front door would only trickle out was because the leak on that valve was also affecting the pressure on the front door. Unreal!! The website and video made it incredibly simple to replace, u guys rock, for real!!!

I followed the video instructions. They were clear and consise. I removed the trim ring and controls. Them removed the housing and flapper. I did notice a small burr in the plastic chute and foam insulation. I trimmed this off with a utility in hopes this burr caused the flapper to warp. This is the 2nd time the flapper has been replaced in 1.5 yrs. The repair was really easy thanks to the video.