ZISW420DRJ General Electric Refrigerator - Instructions

I watched the Video on partselect website for replacing the Solenoid. The repair went smooth. No problem.

Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

Had a water leak on that valve for probably the last 7 or 8 years. Only noticed it when I had a huge water issue with a leaky faucet. Repaired that, went to repair the Sheetrock behind refrigerator and saw water in the tray under frige. Wiggle hose and realized that the reason the water on the front door would only trickle out was because the leak on that valve was also affecting the pressure on the front door. Unreal!! The website and video made it incredibly simple to replace, u guys rock, for real!!!

I followed the video instructions. They were clear and consise. I removed the trim ring and controls. Them removed the housing and flapper. I did notice a small burr in the plastic chute and foam insulation. I trimmed this off with a utility in hopes this burr caused the flapper to warp. This is the 2nd time the flapper has been replaced in 1.5 yrs. The repair was really easy thanks to the video.

Very easy to replace these parts. Thankas to part select for telling me how to do it. You are very helpful.

The video instructions were outstanding in showing how this repair was to be completed. Follow these instructions and Job was very easy. Replaced ice shute flapper and arm, soloinoid and Micro switch for water flow control. Reassemble by reversing procedure. Follow video instructions on how to replace water control valve in back of fridge. Test water flow at bottom front of fridge and defrost flow tube in door if necessary. I used tupperware container with hot water on top of ice shute shelf in fridge door. A couple of times changing and water was flowing. Great site and detailed video instructions for an effective and cost saving self repair. I saved several service trips and service calls and labor costs of a service tect. Parts costs were also a lot cheaper than service tech would have charged. Thanks PartSelect.

remove 3 bucket screws. 1 bracket screw slide bucket back insert drive reverseb steps

Watch to step by step video instructions on your site. Great service! Part arrived the following day after order!

SO easy, just took the old one off and popped the new one in. Why I am bothering to write this is that the first time I ordered the wrong part. I got it so quickly and the refund was made as quickly. Then I tried again and I got it right thet second time. Thanks, Mary

It was exactly as shown in your instruction video

Exactly as the instruction video said. I could have done it without the instructions but I would not have cut a piece off the two water lines and possibly had problems down the road. Also, I may not have figured out the easy way to remove the two lines from the valve body. I believe this is my 3rd time using your process and it's absolutely the best. I won't go anyplace else. Next project is probably replacing the ice maker.

We watched the video on your web site and was very helpful. We ordered the part from your site was here very quickly. It took us about Fifteen minutes to replace. Saved us alot of money. Thanks so much for all your help.

it was easy the only thing was i had to cut old harness to remove 2 wires that went to coil that had to go back in the new harness other then that a peice of cake.

Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.

I reviewed several You Tube repair videos. Not all of them were correct even though my model and brand were specifically mentioned in the videos. Use You Tube with a grain of salt. After sifting through the you tubes, I distilled the information by looking for consistencies. The most inconsistent information was on how to remove the plastic bezels. Once that was figured out, the repair was very easy. Upon removal, I inspected the solenoid. It was very rusted and was no longer capable of pulling the mechanism closed after it had (successfully) opened the flap. The new solenoid fixed the problem in a flash.