Models > ZISW36DXA

ZISW36DXA General Electric Refrigerator - Overview

Get Parts and Repair Help for ZISW36DXA

If you know the refrigerator repair part you need, you can browse the list of all parts on the ZISW36DXA, or you can search by name or part description. You can also find your part by where it is located on the ZISW36DXA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ZISW36DXA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$144.30

Ice Maker

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

$6.62

Dispenser Door Assembly or Flapper

This part mounts in the ice dispenser. **** The crank no longer comes with this part. You can use original crank. The crank is sold separately depending on model number of appliance.

$35.30

Dual Inlet Water Valve

This valve comes with 1/4" compression inlet. NOTE: This part comes with new quick connections. To install - cut retaining nuts off of existing plastic water lines and gently push...

$3.28

SWITCH LIGHT

$63.84

Crushed/Cubed Ice Solenoid Kit

This kit includes 1 cube solenoid, 1 armature, 2 tooth washers and 2 1/4 hex head screws.

$51.12

Defrost Timer - 120V 60Hz

This defrost timer will cycle for twenty-five minutes after every six hours of run time. The timer itself is made of plastic, and its terminals are bent, the leads are internal, and the label is orange.

$6.07

Water Tube Union - 5/16" x 5/16"

Sold individually.

$82.13

Dispenser Control Board - 2 Slide Switches

It is used with those refrigerators that have an ice and water dispenser in the door.

$9.82

Dispenser Grille

This white dispenser grill is located at the bottom of the ice/water dispenser.

$7.89

Actuator Pad

Note: This part is now ONLY available in black.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cracked housing on the vaave

  • Customer: anthony from thornton CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 215 of 232 people found this instruction helpful
1. Turn off water supply, and electrical ( unplug it) to fridge.
2. Remove water line to valve. Watch for water to pour out of the line. Have a towel handy.
3. Remove the cardboard cover on the bottom of the fridge.
4. Remove the screws that hold the valve in place.
5. Remove the valve, be careful the waterlines are still attached.read more

Ice cubes do not dispense because auger does not turn. Bad switch on control board.

  • Customer: Michael from Allen TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 68 of 75 people found this instruction helpful
1) Turn off water line and unplug power.
2) Pop off front panel plate at ice cube select switch area.
3) Unscrew 4 screws that holds control panel housing in place.
4) Remove panel assembly by disconnecting two different wiring plugs.
5) Unscrew 2 screws that allows access to control circuit board at end cap.
6) Remove circuit board ... read more

Sticking Light Switch

  • Customer: Jonathan from Lilburn GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 49 of 54 people found this instruction helpful
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the catch clip so the swi... read more