Models > ZISW36DRC

ZISW36DRC General Electric Refrigerator - Overview

Get Parts and Repair Help for ZISW36DRC

If you know the refrigerator repair part you need, you can browse the list of all parts on the ZISW36DRC, or you can search by name or part description. You can also find your part by where it is located on the ZISW36DRC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ZISW36DRC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$144.30

Ice Maker

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

$33.30

Dual Inlet Water Valve

This valve comes with 1/4" compression inlet. NOTE: This part comes with new quick connections. To install - cut retaining nuts off of existing plastic water lines and gently push them into new valve. To remove - depress ring that the tube slides into.

$3.62

SWITCH LIGHT

$47.63

Defrost Timer

This defrost timer will cycle for twenty-five minutes after every six hours of run time. The timer itself is made of plastic, and its terminals are bent, the leads are internal, and the label is orange.

$5.79

Water Tube Union - 5/16" x 5/16"

Sold individually.

$165.93

Auger and Ice Bucket Assembly

This auger and bucket assembly is used on 25 cubic feet and 27 cubic feet side by side models.

$59.37

Solenoid and Arm Assembly - 120V 60Hz

This solenoid and arm assembly is for the cube/crushed ice.

$7.95

Compressor Relay

The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed.

$10.89

Ice Dispensing Drive Cup

Found at the end of the auger in the ice container - replace when the icemaker doesn't dispense ice.

$4.05

Plastic Tube - 1/4"

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cracked housing on the vaave

  • Customer: anthony from thornton CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 188 of 205 people found this instruction helpful
1. Turn off water supply, and electrical ( unplug it) to fridge.
2. Remove water line to valve. Watch for water to pour out of the line. Have a towel handy.
3. Remove the cardboard cover on the bottom of the fridge.
4. Remove the screws that hold the valve in place.
5. Remove the valve, be careful the waterlines are still attached.read more

Sticking Light Switch

  • Customer: Jonathan from Lilburn GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 43 of 48 people found this instruction helpful
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the catch clip so the swi... read more

The oiginal Ice Bucket auger became rusty and discoloered the ice.

  • Customer: Michael from Antioch CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 42 of 48 people found this instruction helpful
I went on line to find the part. Luckily I found PartSelect.com. All I had to do was enter the model number into the search box and scroll through the list of parts.
I ordered the part over the weekend and recieved it on Tuesday!
All I had to do was remove 4 screws from the original Ice Bucket and attach the new one.
Perfect fit in under 15 mi... read more