ZISB420DRF General Electric Refrigerator - Instructions

Had a water leak on that valve for probably the last 7 or 8 years. Only noticed it when I had a huge water issue with a leaky faucet. Repaired that, went to repair the Sheetrock behind refrigerator and saw water in the tray under frige. Wiggle hose and realized that the reason the water on the front door would only trickle out was because the leak on that valve was also affecting the pressure on the front door. Unreal!! The website and video made it incredibly simple to replace, u guys rock, for real!!!

I followed the video instructions. They were clear and consise. I removed the trim ring and controls. Them removed the housing and flapper. I did notice a small burr in the plastic chute and foam insulation. I trimmed this off with a utility in hopes this burr caused the flapper to warp. This is the 2nd time the flapper has been replaced in 1.5 yrs. The repair was really easy thanks to the video.

Very easy to replace these parts. Thankas to part select for telling me how to do it. You are very helpful.

The video instructions were outstanding in showing how this repair was to be completed. Follow these instructions and Job was very easy. Replaced ice shute flapper and arm, soloinoid and Micro switch for water flow control. Reassemble by reversing procedure. Follow video instructions on how to replace water control valve in back of fridge. Test water flow at bottom front of fridge and defrost flow tube in door if necessary. I used tupperware container with hot water on top of ice shute shelf in fridge door. A couple of times changing and water was flowing. Great site and detailed video instructions for an effective and cost saving self repair. I saved several service trips and service calls and labor costs of a service tect. Parts costs were also a lot cheaper than service tech would have charged. Thanks PartSelect.

remove 3 bucket screws. 1 bracket screw slide bucket back insert drive reverseb steps

Watch to step by step video instructions on your site. Great service! Part arrived the following day after order!

SO easy, just took the old one off and popped the new one in. Why I am bothering to write this is that the first time I ordered the wrong part. I got it so quickly and the refund was made as quickly. Then I tried again and I got it right thet second time. Thanks, Mary

It was exactly as shown in your instruction video

First, I replaced my water filter but when it didn't work I googled the problem and the most advice I found was the double outlet water valve must be bad. SO I ordered the parts thru parts select. But when I installed the valve, the water dispenser still didn't working. I went back to parts select website and to see if somebody had the same problem. A gentlemen posted that if the water line is frozen, no water will come out. So I defrosted my refrigerator and turned it on again and it finally work. So now, I wasn't sure if the REAL problem I had was just frozen line or a bad valve. I decided to keep the water valve since my ref was almost 10yrs old. (But I still don't know why my water line froze.)

I had to defrost the freezer to free the icemaker. After that the installation was plug and play with two small exceptions: 1) I had to file down the width of the left hand tine of the old stripper so that it would fit the new icemaker, and 2) the motor housing of the new icemaker was slightly wider than the old one. It fit, but just barely. But I'm back in the ice again, no dripping water, all is good.

My refrigerator was making a high pitched kind of howling noise. The PartSelect symptom that was closest was “unusual noise” and when I clicked that it said the evaporator fan motor fixes the symptom 32% of the time. Since my freezer fan speed sounded like it was constantly changing I went ahead and bought one which PartSelect delivered promptly. The installation video was great and although my freezer was not identical to the one in the video, the video was still very helpful. The only thing it didn’t say was how to tell if my freezer motor was the one with the thermistor although I suspect that they all are and that PartSelect is simply trying to save us money by showing us how to splice in a motor without a thermistor. Anyway, since I would have had to disassemble the freezer before buying the part to find out for sure, I just bought the one without the thermistor. This just meant I had to splice the new motor in, just like in the video. I think I would have preferred buying the motor with the thermistor even though it was more expensive. In the end my problem is solved so I’m happy. This is the third time that I’ve had to repair this GE refrigerator and PartSelect has been a valuable resource each time.

The repair is easy enough, only problem I had was that I ordered the wrong part initially. Unfortunately, on the parts schematic there are two different parts listed and I didn't realize it. I did not look at my water valve prior to ordering, and naturally ordered the wrong one. One good thing, with the wrong part, there is a video showing the repair which I had watched. When I got the right part, the repair was basically the same as the video.

The parts fit perfectly, and the on-line video helped me determine how everything fit back together. Thanks,Rudy

I researched the issue on line and replaced the microswitch. I didn't test the part since it was so inexpensive and the whole process only took me about 15 minutes to complete. I didn't know "where" the microswitch was located until I watched your video, a very helpful tool. Thanks PartSelect, the part arrived 3 days after I ordered it.Mike in Spokane, WA

Followed the video demo and would have been done sooner but for limited work space- narrow freezer compartment and the release tabs on the electrical plug. First home repair that the air was not blue and got done in under time allocated.