ZISB420DRC General Electric Refrigerator - Instructions

I just followed the directions carefully, loosened the screws with a nutdriver removed the unit from the screws, unplugged the unit from the freezer plug, took out the new unit, used the adapter supplied with the unit to match up with the plug in the freezer, carefully attached the icemaking unit to the screws, carefully slid the cord behind the unit, lightly clinched down the screws, checked it with a level and then did the final snug down. turned the unit on and it worked fine. Pretty easy, just take your time, don't rush and it will come out fine.

I watched the video on the PartSelect.com website and decided to give it a try. The replacement of the flapper was even easier than I anticipated! The old flapper was extremely warped and was allowing air into the freezer. I'm not sure how/why it was in that condition but I am happy to report that I have no more ice buildup. Thank you, PartSelect!

Put spring on. Hardest part is the amount of space to work in. Clean under fridge first.

Since my refrig is 18 yrs. old and I never had to replace it, took a little long to remove trim piece on the outside. After that repair went smoothly. I still have problem with water collecting inside on the bottom of the freezer, might have a leak somewhere. Ice maker is functioning correctly.

luckly i have a bit of experience in refrigeration im an hvac technician by trade. this repair was a bit tricky in that i did not know at first if it was a Temperature Sensor issue or the main control board. I had tested the defrost termination thermostat and the defrost heater and as i suspected they were ok. Next i wanted to test the thermistors (temp sensors) it is hard to find technical data on these fridges. I needed to test the thermistors resistance @ a certian temperature to ensure they were working properly but where do u get such data? I also wanted to know some information about the logic programmed into the board (i.e when do you initiate defrost etc. . .). I had no such luck so i figured since i tested the defrost heater and thermostat and they were ok and all of the evap fans and such were working i'd order a circuit board and new thermistors. Got the CORRECT PARTS from this site in 2 business days and my fridge is working great! changing the parts was really easy, figuring out which parts to change was the only difficult thing about this job.

My son replaced both temperature sensors and the fridge works great now!!! Like brand new again!!!!

Removed frame, unscrewed the electrical panel, and popped the flapper off. Installed new flapper. Replaced the electrical panel and re-installed the frame.

Removed the ice maker control panel and accessed the flapper door, easy switch out for new door and seal. The 2 year old warped seal didn't close and so ice crystals formed in the freezer - new unwarped part and Ta-Da no more problems :)

1.Unplug and turn off water supply to refrigerator. 2.Remove several screws from back panel and remove panel 3. Remove water supply line from valve. 4. Remove screw holding valve on using 1/4" nut driver or socket. 5.Remove the 2 electrical plugs and 2 water lines from valve. 6.reinstall in reverse order. This is a 5 minute job at best. Good Luck! I had my fridge in storage for several years and when it froze it cracked the storage tank PS783769 I replaced it first and found valve was leaking after tank was replaced.

Popped off the front frame and front of mother board. unscrewed the assembly to be able to lift up to get to flapper. Lifted it up out of the the way ( wires are attached so it may take one other person to hold it up out of the way). Pop out the old flapper and replace with new one. Easy !

Repair went exactly like the video. With this video it was easy to make the repair. There were no surprises or problems and I felt confident in the videos instructions. It was like pushing the easy button.

Part shipped in 2 days after requesting basic mail. Video was exremely accurate, no surprises. Valve replacement DID NOT fix my problem, however. I had to twist the water filter plug on and off a few times to release better pressure. My issue appeared to be with filter mount shut off. Still cheaper than a repair man!

Installed a dual water inlet valve.. by turning off the water and unplugging the refrigerator. use a nut driver to remove the screws and removed the connector to the inlet valve.. installed the valve and reverse the procedure. it was very ease also the Part Select troubleshooting information and instructions was very helpful..

What an awesome site! After putting in my model number and finding the problem I was having, I simply picked the 2 parts that were most likely to solve the problem. I bought a defrost thermostat, and defrost heater. To a high certainty, they would solve my problem. They didn't however! I ended up having to buy a temperature sensor on another order a few weeks later when the problem resurfaced! My own fault. I should have bought it the first time. As others have written: the longest part of the job is defrosting the ice from the coil. One thing I did that I didn't see suggested: plug the drain hole below the coil. I put a couple towels in the bottom of the freezer and ran the hair dryer. Didn't take long. I read that the amount of water created will overflow the pan under the refrigerator, so I plugged the drain hole. Once you clean that mess up, the repair is pretty straight forward. Great site. Even through I had to make two separate purchases, I still saved a lot of money. Thanks!

Checked to make sure it wasn't a plumbing problem. Then made aide sure the filter wasn't plugged. Then went to Parts Direct's web site. According to their information, the most likely problem was the duel inlet water valve. I followed to video instructions provided on the web site...finished the job in less than 15 minutes...and solved the problem. I will certainly be using your service in the future!