Models > ZIS48NSC

ZIS48NSC General Electric Refrigerator - Overview

Get Parts and Repair Help for ZIS48NSC

If you know the refrigerator repair part you need, you can browse the list of all parts on the ZIS48NSC, or you can search by name or part description. You can also find your part by where it is located on the ZIS48NSC by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ZIS48NSC parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$137.62

Ice Maker

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

$19.30

Single Outlet Valve Kit

This single outlet valve has 1/4 inch compression fittings, and is intended for use with refrigerators that have ice makers that make crescent shaped ice cubes. NOTE: As per the manufacturer this valve has new quick connection. You must cut retaining nut off of the current plastic water line and gently push it into new valve. To remove, depress ring that the tube slides into.

$5.79

Water Tube Union - 5/16" x 5/16"

Sold individually.

$7.95

Compressor Relay

The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed.

$14.54

Fill Tube Grommet

This fill tube grommet is used on the icemaker.

$18.16

Ice Bucket - White

$137.62

Condenser Fan Motor - 115V

This part comes with 3 round pin connection terminals. This fan motor circulates the air through the refrigerator grille and cools the compressor and condenser coils. It also helps...

$18.76

Defrost Timer

This refrigerator defrost timer will cycle for thirty minutes after every ten hours of run time.

$3.62

1/4 Tubing Nut

$3.62

Plastic Tube - 1/4"

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice stalactites were drooling out of the icemaker and gumming up the cubes in the receiving tray.

  • Customer: Gerald from Benicia CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 38 of 40 people found this instruction helpful
I first shut off water flow to the fridge. Examination of the package (which was not exact in appearance to the original) demonstrated that the electrical connectors were well-insulated so I arrogantly and successfully proceded without disconnecting the power. My fridge is old enough that the model doesn't appear exactly on anyone's list so I wasn't alarmed... read more

Sticking Light Switch

  • Customer: Jonathan from Lilburn GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 35 of 39 people found this instruction helpful
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the catch clip so the swi... read more

FREEZER & FRIG WERE NOT COLD

  • Customer: Sam from Cooper City AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 31 of 48 people found this instruction helpful
First I removed the rear cover, located at the bottom of the refrigerator. Then I cleaned out the dirt & dust on and around the compressor. The relay has a cover, that is secured with a spring loaded clip. To release the clip, push in with your fingers, while disengaging the end clip with a screwdriver. Once one side is off the other lifts off. Remove c... read more