Models > ZFSB27DYASS

ZFSB27DYASS General Electric Refrigerator - Overview

Get Parts and Repair Help for ZFSB27DYASS

If you know the refrigerator repair part you need, you can browse the list of all parts on the ZFSB27DYASS, or you can search by name or part description. You can also find your part by where it is located on the ZFSB27DYASS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ZFSB27DYASS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$2.52

Light Bulb - 40W

Sold individually.

$6.20

Dispenser Door Assembly or Flapper

This part mounts in the ice dispenser. **** The crank no longer comes with this part. You can use original crank. The crank is sold separately depending on model number of appliance.

$137.62

Ice Maker

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

$18.07

Drawer Slide Rail - Right Side

$15.92

Drawer Slide Rail - Left Side

When looking inside the fridge, this white drawer slide rail is located on the left side of the refrigerator. Rail ONLY.

$4.21

Bearing Slide

Sold individually.

$33.30

Dual Inlet Water Valve

This valve comes with 1/4" compression inlet. NOTE: This part comes with new quick connections. To install - cut retaining nuts off of existing plastic water lines and gently push...

$18.32

Drawer Slide Rail - Right Side

$3.22

SWITCH LIGHT

$26.64

Defrost Timer

This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cracked housing on the vaave

  • Customer: anthony from thornton CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 185 of 202 people found this instruction helpful
1. Turn off water supply, and electrical ( unplug it) to fridge.
2. Remove water line to valve. Watch for water to pour out of the line. Have a towel handy.
3. Remove the cardboard cover on the bottom of the fridge.
4. Remove the screws that hold the valve in place.
5. Remove the valve, be careful the waterlines are still attached.read more

Refrigerator temp was warm

  • Customer: Adrian from Louisville KY
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 88 of 99 people found this instruction helpful
Per the trouble shooting guide on the home page of the website. I suspected the defrost timer was bad because ice had heavily accumulated on the back wall of the freezer compartment and the temperature inside the refrigerator was warm. First, I removed all the freezer racks. Then removed the (4) screws on the back wall in the freezer compartment. I then ... read more

Ice cubes do not dispense because auger does not turn. Bad switch on control board.

  • Customer: Michael from Allen TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 61 of 65 people found this instruction helpful
1) Turn off water line and unplug power.
2) Pop off front panel plate at ice cube select switch area.
3) Unscrew 4 screws that holds control panel housing in place.
4) Remove panel assembly by disconnecting two different wiring plugs.
5) Unscrew 2 screws that allows access to control circuit board at end cap.
6) Remove circuit board ... read more