Models > ZFSB26DNDSS

ZFSB26DNDSS General Electric Refrigerator - Overview

Get Parts and Repair Help for ZFSB26DNDSS

If you know the refrigerator repair part you need, you can browse the list of all parts on the ZFSB26DNDSS, or you can search by name or part description. You can also find your part by where it is located on the ZFSB26DNDSS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ZFSB26DNDSS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.82

Light Bulb - 40W

Sold individually.

$9.20

Temperature Sensor

Also known as Thermistor. This part is used to sense the temperature in the cabinet.

$46.00

Dual Inlet Water Valve

This double outlet water valve has quick connections. This valve has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.

$10.25

Defrost Thermostat

This part acts as a safety device against over heating in case of mechanical failure.

$151.68

Main Electronic Control Board

This board controls the operation of the unit. Note: This part has been updated by the manufacturer. It may differ in appearance but will function the same as the original.

$62.79

Ice and Water Filter

Sold individually. NOTE: As per the manufacture this is an updated water filter. If you have never installed the updated filter or your old filter was made by Culligan, you may need the adapter to install the filter. GE Refrigerator Water Filter. If you have never installed this new style filter or your old filter was made by Culligan you may need the adapter to install it.

$31.30

Dispenser Door Solenoid Assembly

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

$6.20

Dispenser Door Assembly or Flapper

This part mounts in the ice dispenser. **** The crank no longer comes with this part. You can use original crank. The crank is sold separately depending on model number of appliance.

$144.30

Ice Maker

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

$52.16

Defrost Heater and Bracket Assembly

The defrost heater keeps the cooling coils from frosting over. The heater will get hot and melt any ice or frost build up around the coils.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigertor water dispenser not working BUT ice machine is working

  • Customer: ralph from bristow VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 497 of 543 people found this instruction helpful
The very first symptom here is important! The door water dispenser is not working but the ice macine is working. You may only have a frozen water tube in the door so do the following before diagnosing that your solenoid valve is bad: 1) the tube usually runs under the front of the refrigerator and usually has a quick disconnect. Undo the connection and pr... read more

The refrigerator made continous "whooing" sounds that increased and decreased in pitch. Sounded like a ghost. Would keep us up at night. Also noticed that the heater was not heating under the evaporator coils.

  • Customer: John from Holly Springs NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 275 of 303 people found this instruction helpful
After checking the stories, the consensus of opinion was to change the mother board. I had a tremendous help from Tom Paone at quality@applianceeducator.com. He also told me to change the motherboard but to make sure that the coils were totally defrosted before starting up the refrigerator after changing the board.

Took off three nuts around the b... read more

flap to ice dispenser would not close

  • Customer: Bill from Cleveland Heights OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 172 of 187 people found this instruction helpful
The flap to the ice dispenser would not close, which allowed the ice dispenser to frost up, freezing the water dispenser.

This was a simple fix. The solenoid had stopped working, so it would not automatically close the door flap. I read some posts on this site that suggest that you had to remove the trim around the entire dispenser to get at the... read more