Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ZFSB23DNASS

ZFSB23DNASS General Electric Refrigerator - Overview

Get Parts and Repair Help for ZFSB23DNASS

If you know the refrigerator repair part you need, you can browse the list of all parts on the ZFSB23DNASS, or you can search by name or part description. You can also find your part by where it is located on the ZFSB23DNASS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ZFSB23DNASS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

Order within the next 1 hr and 31 mins and your part ships today!
$10.98

Temperature Sensor

This temperature sensor, also known as a thermistor, is used for refrigerators and freezers. The sensor sends the temperature reading of the refrigerator towards the control board. If your refrigerator or freezer runs too long, is too warm, will not defrost, or has sections that are too cold, replacing this part is the solution. Before replacing the temperature sensor, make sure to unplug the fridge for safety. The tools needed for this repair are a nut driver, wire crimper, and wire splice connectors. Search your model number to ensure the correct part is ordered and refer to model specific diagrams/owners manual for the exact instructions.

Order within the next 1 hr and 31 mins and your part ships today!
$54.73

Dual Inlet Water Valve

This double outlet water valve has quick connections. This valve has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.

Order within the next 1 hr and 31 mins and your part ships today!
$12.82

Defrost Thermostat

This defrost termination thermostat acts as a safety device to stop the evaporator coil from overheating, by turning off the defrost heater at the end of the defrost cycle. The thermostat measures the temperature in your freezer to ensure that it stays at an optimum temperature to keep your frozen food from thawing. Some common symptoms linked to a faulty defrost termination thermostat include: the freezer is not defrosting, is too cold/too warm, or there is a frost build up in the freezer. Before you decide to replace this part, ensure that there is no frost build up in your freezer; as a build up can interfere with the thermostat reading.

Order within the next 1 hr and 31 mins and your part ships today!
$63.92

Ice and Water Filter

This is an ice and water filter. The most common reason you would need to change this part is if you have never updated your model and it is no longer filtering your water. This al...

Order within the next 1 hr and 31 mins and your part ships today!
$18.45

Module Shelf Insert

This part is located in the front of the module shelf.

Order within the next 1 hr and 31 mins and your part ships today!
$41.11

Dispenser Door Solenoid Assembly

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

Order within the next 1 hr and 31 mins and your part ships today!
$7.36

Dispenser Door Assembly or Flapper

The dispenser door assembly (or flapper) is what opens to release the ice once the lever has been pressed. This part mounts in the ice dispenser. The cranker no longer comes with this part. You can use the original crank. The crank is sold separately depending on the model number of the appliance. For this repair, all you will need is a Phillips screw driver and a small flat blade. Disconnect the power, remove the escutcheon from around the dispenser, lift up the control panel, disconnect all wire connectors, use a screwdriver to remove all four screws of the housing, and lift the housing out. You will now see the flapper: push the tabs that are securing it in place to remove the piece, install the new flapper by lining it up and snapping into place.

Order within the next 1 hr and 31 mins and your part ships today!
$155.85

Ice Maker

This is a replacement ice maker kit, it is used in the freezer section of your refrigerator. This particular model will produce seven round or crescent shaped cubes every cycle. Th...

Order within the next 1 hr and 31 mins and your part ships today!
$26.87

Water Tank Assembly

This tank stores water until the water actuator is activated and water is requested.

Order within the next 1 hr and 31 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigertor water dispenser not working BUT ice machine is working

  • Customer: ralph from bristow, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 930 of 1013 people found this instruction helpful
The very first symptom here is important! The door water dispenser is not working but the ice macine is working. You may only have a frozen water tube in the door so do the following before diagnosing that your solenoid valve is bad: 1) the tube usually runs under the front of the refrigerator and usually has a quick disconnect. Undo the connection and pr... read more

Fridge too warm, evaporator icing up

  • Customer: Gerald from San Clemente, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 447 of 535 people found this instruction helpful
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wir... read more

flap to ice dispenser would not close

  • Customer: Bill from Cleveland Heights, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 382 of 440 people found this instruction helpful
The flap to the ice dispenser would not close, which allowed the ice dispenser to frost up, freezing the water dispenser.

This was a simple fix. The solenoid had stopped working, so it would not automatically close the door flap. I read some posts on this site that suggest that you had to remove the trim around the entire dispenser to get at the... read more