ZEU669T1WW General Electric Cooktop - Instructions

1) Turn Power off at Circuit Breaker
2) Lift Cooktop out of counter top.
3) Remove all dials from controls by pulling straight up.
4) Remover glass plate which covers burners by removing
screws along outer edge.
5) Remove the two top screws from the control to be
replaced (this holds the infinite control to bracket)
6) Remove one wire at a time from the old control and
plug on the new one in correct orientation.
7) Reverse above order to reassemble.

(Note: Not all infinite controls are same PN when
ordering, the drawingings are deceiving that they are)

You have to replace the switch if the shaft breaks (I think we hit it with a pot). This is a flat glass cook top. Turn off the power at the breaker box. I took the drawers out below the cook top and loosened the bracket holding the electrical conduit. That allowed me to push up the cook top from below. There is some adhesive but nothing hold it except its own weight and the adhesive. You do not need to disconnect the conduit. Remove all of the knobs. Remove all of the Phillips screws around the upper perimeter. Do not remove any of the hex screws yet. When all of the screws are removed, lift the glass cook top off of the metal "guts." At this point there will only be adhesive holding it on. Now remove two hex screws at each end of the control strip. Remove the two Phillips screws from the subject switch. Lift up the the control strip, disconnect the electric leads to the switch, reconnect the leads to the new switch, and then re-attach the new switch to the control strip with the two Phillips screws. Then go backwards. Replace the control strip and secure with the two hex screws at each end. Before replacing the cook top, check the burners. They rest on posts with small springs designed to keep them flush with the glass cook top. Make sure that all of the burners are properly aligned on their posts and springs. Replace the cook top and re-attach with all of the Phillips screws. Return the cook top to its resting place making sure the adhesive strips are correctly placed around the perimeter. Replace the bracket on the conduit. Put the knobs back on. Flip the breaker back on and start cooking.

using the info on this site i guessed it was the switch. It was. this is a Radiant Heat in counter drop on cook top. i was nervous about getting it out of the counter but that was eassy, just sits on top. the One issue was diconnecting the BX electric cable from the elecric box. mine did not have threads and a nut. but a push in fitting with small tabs.. i forced it out by pushing the tabs in with a screw driver.. later found out it was a band that was eassily removable by just prying it open with a screw driver... and later replacing it.. the glas removal was just screws and the switch was insised a cover with four screws.. plugged the new one in (careful to keep the connections the same, and reversed the process.. ready to fix it again if needed!thanks for having the part... probably saved $200! can take less than 30 minutes if you get past the electric connection quicker than i did... that;s it!

Removed counter top stove, released zip ties on flex conduit,removed cover glass, removed switch anchor panel, removed old switch,(noting the color of each wire) replaced switch reassembled.

Turned off power to cooktop. Disconnected power wires and removed cooktop from counter. Removed screws holding on the cooktop surface. Separated cooktop surface from cooktop. Removed 4 screws holding control panel, then removed 2 screws holding selector switch. Removed 2 wires plugged into selector switch. Installed new selector switch and reassembled cooktop.

1) SHUT OFF POWER
2) Removed the cooktop from the counter
3)Remove 6 screws holding the cooktop glass frame to the housing
4)Removed 4 screws holding the switch retainer to the housing
5)Removed 2 screws holding the switch in place
6)Moved one wire at a time from the old switch to the new switch
7)Reassembled

Removed unit from counter top. Opened to locate wiring diagram. Identified part snd searched on internet. PartSelect.com provided all missing information and had easy to follow instructions...confirming my initial assessment of the problem. Ordering was easy; delivery fast. Job completed.

turn off breaker, two screws hold down cooktop, 8 screws take top off cooktop. unplug switch, install new switch. repair loose connections. put back together. pretty simple

Remove ten screws that attach top then remove top. Remove four screws holding switches in place and lift for access. remove two screws from switch. Record wire color for positions P L1 L2 for proper positioning on replacement switch. One wire was to short so had to make a two inch extension to complete the hookup. Reassemble and the burners work as original.

1. Turned of circuit breaker to stove.
2. Take two screws out of control panel, and lifted it up.
3. Lay panel on side and removed knob.
4. Flipped panel over and take several pic for reference of each wire and location on back of controller.
5, Flipped panel back over and take needle-nose players and unhooked each wire tab on back of controller.
6. Flipped panel back over and take two screws out that hold controller on front of panel.
7. Flip the panel back over and remove the old controller.
8. Position the new controller in the panel and install the the two screws back to secure it to the panel.
9. Attach wires back to new controller based on your pic taken. Verify correct location to pic.
10. Attached panel on back of stove. Make sure all wires are secured inside of the control panel.
11. Turn circuit breaker back on and verify the burner is working correctly.

Turn off breaker.
Lift cook top from counter.
Remove perimeter screws from glass cook top and remove glass.
Remove screws attaching control.
Replace control and leads.
Note: 4 of 5 lead attachment marking points matched old control - I had to guess the fifth. "P" on old was attached to "PC" on new. Attachment points on new were configured differently from old. The leads were just barely long enough to reach.
Replaced perimeter screws and cooktop.

Turn off breaker removed cooktop from countertop . Removed Phillips screws remove glass top .Remove two screws holding switch & reinstalled

Remove stove top from cabinet. surf for you tube videos to replace switch.

Remove screws from 2 sides of cook top, lift out top frame/glass assembly, element controls are to your right. Remove screws on top and bottom of element control assembly to access wiring and inspection. The 4 element controls, 4 heating coils, and all internal wiring were check for shorting, open circuits, and signs of burned parts. My trusty Fluke meter found a Halogen Element control shorted to ground. I order the part from Parts Select.com it came the next day Fantastic Service !! I'm happy, my wife's happy!

Raised cooktop......took 8 screws from trim plate and cook surface off.....removed 4 more screws off switch mount bracket, removed 2 screws from switch and mount bracket ( switch now free) ...pulled off wires and connectors one at a time, and put the wire on corresponding new switch location.... Took a total of 30 minutes.... Cleaned cooktop surface too! Cautions...don't tighten ANY screw too tight, as stripping will occur.