Models > ZET958SF1SS

ZET958SF1SS General Electric Oven - Overview

Get Parts and Repair Help for ZET958SF1SS

If you know the oven repair part you need, you can browse the list of all parts on the ZET958SF1SS, or you can search by name or part description. You can also find your part by where it is located on the ZET958SF1SS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your oven. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.73

Oven Sensor

This temperature sensor detects the temperature within the oven cavity.

Order within the next 4 hrs and your part ships today!
$17.95

Broiler Pan - Large

Includes the pan and grate.

Order within the next 4 hrs and your part ships today!
$4.48

SCREW

Order within the next 4 hrs and your part ships today!
$57.02

Broil Element

This broil element is found on the roof of the oven.

Order within the next 4 hrs and your part ships today!
$37.80

WINDOW PACK ASM

Order within the next 4 hrs and your part ships today!
$1.93

Screw

This screw is sold individually.

Order within the next 4 hrs and your part ships today!
$47.84

Convection Element

Order within the next 4 hrs and your part ships today!
$2.79

Screw

Sold Individually.

Order within the next 4 hrs and your part ships today!
$3.00

Screw

Sold Individually.

Order within the next 4 hrs and your part ships today!
$60.02

Lower Oven Door Gasket

Order within the next 4 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven was not coming up to temperature

  • Customer: Sean from Highlands Ranch CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 21 of 25 people found this instruction helpful
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very e... read more

Broil (top) element replacement for oven

  • Customer: robert from pine valley CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 17 of 18 people found this instruction helpful
After turning the breaker off, using a 1/4 inch nut driver I removed all the clamp screws (5) holding the heating element in place. I then unplugged the element wire spades from the rear of oven and removed the old element. Installing the new one was simply going in reverse order. After plugging the new one in, I did however, use plyers to squeeze the connec... read more

Aluminum Foil Bonded With Bottom

  • Customer: Linda from Oro Valley AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 12 of 13 people found this instruction helpful
It was much easier than trying to remove the bonded aluminum foil from the false bottom/drip pan. Simply lift and remove oven front door, (see your manual), slide out false bottom and slide in new. For me it did take longer than 15 minutes, but that's because I was doing a thorough oven cleaning. The part was in the $50 range and well worth it. Why didn't an... read more