Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ZEK754GP1

ZEK754GP1 General Electric Wall Oven - Overview

Get Parts and Repair Help for ZEK754GP1

If you know the wall oven repair part you need, you can browse the list of all parts on the ZEK754GP1, or you can search by name or part description. You can also find your part by where it is located on the ZEK754GP1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. We’ve also included any installation videos we have for ZEK754GP1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the ZEK754GP1

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$5.30

Single Heating Element Support Clip

The metallic clip, or also known as a broil element support, is for a oven element on a range. This part holds the broil element in place on top of the oven. If your support clip i...

Order within the next 41 mins and your part ships today!
$52.17

Bake Element

This bake element is used in ranges and located at the bottom of the oven. The bake element supplies heat for baking. If your symptoms include: your oven is not heating evenly, not starting, or the heating is not consistent, then replacing the element can be the solution. Remove two retaining screws, make sure to disconnect the two connecters at each end of the element, and replace with the new one. Before starting this replacement, make sure the range is unplugged from the power source or shut off from the house circuit breaker. The tool needed is a Phillips screwdriver.

Order within the next 41 mins and your part ships today!
$47.38

Broil Element - 240V

This oven broil element has push-on terminals.

Order within the next 41 mins and your part ships today!
$104.90

Oven Sensor

It is possible that your oven is cold because of a fault in the temperature sensor. The temperature sensor regulates oven temperature in modern ranges, like a thermostat. It is on the back wall near the broiler on the top wall. On a newer oven, there may be a fault code displayed. Faulty temperature sensors are often responsible for F3 and F4 error messages on an electric range. Check your manual or the manufacturer website to find out the proper resistance of the temperature sensor. To check your sensor, unplug the oven and use a multi-meter to see if your sensor is at the correct resistance.

Order within the next 41 mins and your part ships today!
$3.29

SCREW

Sold Individually.

Order within the next 41 mins and your part ships today!
$2.06

Screw

This screw is sold individually.

Order within the next 41 mins and your part ships today!
$18.56

Broiler Pan - Large

This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain....

Order within the next 41 mins and your part ships today!
$3.29

Screw

Sold Individually.

Order within the next 41 mins and your part ships today!
$5.30

Light Cover

This light bulb lens covers the interior light bulb in an oven, range, or stove. No tools are necessary to replace this part. Simply slide off the wire bracket to remove the existi...

Order within the next 41 mins and your part ships today!
$51.99

RACK OVEN

Sold individually.

Order within the next 41 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven tempature was approximately 150 degrees to low

  • Customer: James from Austin, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 198 of 226 people found this instruction helpful
This repair is EASY if you know how to use an ohm meter. If not, seek help for this step.

SYMPTOM:
The oven (JKP27WOP3WG or JKP27WP3WG and many ovens like it ) was not getting hot enough. Verifying the cooking temperature with an typical oven thermometer, I was able to determine that the oven was cooking temperature was about 150 degrees t... read more

bake element shorted out, sparking like a sparkler

  • Customer: Carl from Wynnewood, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 77 of 82 people found this instruction helpful
first, made sure circuit breaker was off
second, used nut driver to remove 2 screws on old element, pulled it from the back of the oven
third, removed 2 wires from old element (spade connectors)
fourth, connected new element and pushed back into oven.
fifth, reinstalled 2 screws securing new element

this was all done by my 15 y... read more

The broiler element caught fire and burned out while I was broiling a steak.

  • Customer: Dianne from Rockville, MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 50 of 57 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches, but I had not turned off the power.
So, I shorted out one of the wires. Then I turned off the power but was afraid to go any farther.
An appliance repairman was at my house that day fixing my dryer seal. He was able to pull the wires through... read more