This is a lower rack roller for your dishwasher. It attaches in the lower roller assembly on the bottom of your rack to allow the rack to smoothly slide in and out. This replacement part is 1.5 inches...
$13.13
In Stock
Order within the next 11 hrs and your part ships today!
This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a bro...
$44.23
In Stock
Order within the next 11 hrs and your part ships today!
This mounting bracket is manufactured to secure your dishwasher to your countertop. Mounting brackets should be installed so the dishwasher doesn’t tip forward. You can fit the bracket to either the c...
$7.49
In Stock
Order within the next 11 hrs and your part ships today!
This is a genuine GE dishwasher leveling screw. It operates as a leg on the bottom of your dishwasher, and can be screwed in and out to raise and lower the height of the dishwasher. It is made of meta...
$8.06
In Stock
Order within the next 11 hrs and your part ships today!
This part is a replacement middle spray arm bearing for your dishwasher. The spray arm bearing reduces friction and allows the spray arm to rotate during the operating cycle. If the spray arm is not r...
$13.88
In Stock
Order within the next 11 hrs and your part ships today!
This lower rack assembly is a genuine OEM replacement part that is made for dishwashers. It consists of the sliding rack with tines that hold dishes in place during the wash cycle. The lower rack is d...
$165.77
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for ZDT975SSJ2SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jason
November 19, 2021
Dishwasher wasn't filling with water occasionally. The problem became more frequent and then most of the time. I replaced the water intake valve. Same problem. I went through the service mode and discovered problem codes F65 "Inverter No Water Detected" and F37 which isn't listed as one of the codes in the service instructions. F36 is "CSM Trip" but that isn't listed. Any ideas on what to replace or test? BTW, when I attempt to run the load tests such as water fill, nothing happens and the codes appear.
For model number ZDT975SSJ2SS
Hello Jason, Thank you for the question. If the Water Valve did not fix the issue, shut off power to the dishwasher and check inverter control board wiring. Reconnect any loose wires. Replace the wire harness if damaged. If the wiring is okay, replace the inverter control board. We hope this helps!
1. Turn off breaker supplying power to dishwasher in electrical panel 2. Open dishwasher door 3. Unscrew the screws that secure the dishwasher to the counter. 4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch. 5.
... Read more On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside. 6. Remove old door latch. 7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in. 8. Plug wire harness into new door latch. 9. Re-align dishwasher and re-secure to counter in previous position. 10. Test latch to make sure it closes properly. 11. Turn on breaker in electrical panel. The dishwasher should now function properly.
Replaced transition piece, gasket, and vent cover. The root cause problem is that the factory installed gasket was too thick and would not allow sufficient thread engagement. The replacement gasket was about 25% thinner and worked perfectly.
the design of this part is easy to break when closing the top rack.
there is a hub that clicks in place and a spinner within this that makes the water spray evenly on the top of the tub of the dishwasher
the part broke when closing the rack [a dish too tall hit it]
it took less than 5 minutes to replace as
... Read more the part just clicks into two edge spots i did this without removing the rack or even looking into the tub all by feel
