Models > ZDP304NT1SS

ZDP304NT1SS General Electric Range - Overview

Sections of the ZDP304NT1SS

[Viewing 9 of 9]
Body Parts Diagram and Parts List for General Electric Range
Body Parts
Control Panel Diagram and Parts List for General Electric Range
Control Panel
Convection Fan Diagram and Parts List for General Electric Range
Convection Fan
Cooktop Diagram and Parts List for General Electric Range
Cooktop
Door Assembly Diagram and Parts List for General Electric Range
Door Assembly
Door Lock Diagram and Parts List for General Electric Range
Door Lock
Gas And Burner Parts Diagram and Parts List for General Electric Range
Gas And Burner Parts
Monogram Customization Diagram and Parts List for General Electric Range
Monogram Customization
Oven Cavity Parts Diagram and Parts List for General Electric Range
Oven Cavity Parts
Keep searches simple, eg. "belt" or "pump".
Temperature Sensor – Part Number: WB21X22134
Temperature Sensor
★★★★★
★★★★★
(48)
PartSelect #: PS10059162
Manufacturer #: WB21X22134
The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature ...
$38.48
  In Stock
Door Handle Fastener – Part Number: WR01X11007
Door Handle Fastener
★★★★★
★★★★★
(8)
PartSelect #: PS6447735
Manufacturer #: WR01X11007
This is a door handle fastener to secure the handle to your refrigerator drawer. It is also known and a mounting bolt or screw. It is approximately 1 inch in total length, and is made of metal.
$13.15
  In Stock
SCREW – Part Number: WB1X536
SCREW
PartSelect #: PS234785
Manufacturer #: WB1X536
$9.70
  In Stock
BOARD SENSOR – Part Number: WB27X28659
BOARD SENSOR
PartSelect #: PS12170456
Manufacturer #: WB27X28659
$22.73
  In Stock
Screw – Part Number: WB01K10002
Screw
PartSelect #: PS221932
Manufacturer #: WB01K10002
Size: 8-32 inch Sold individually.
$20.97
  In Stock
NUT – Part Number: WB02T10017
NUT
PartSelect #: PS223451
Manufacturer #: WB02T10017
$9.70
  In Stock
SPRING IGNITER – Part Number: WB09T10011
SPRING IGNITER
PartSelect #: PS1480944
Manufacturer #: WB09T10011
$8.08
  In Stock
SCREW 8-32 MCH PNT15 – Part Number: WB01T10104
SCREW 8-32 MCH PNT15
PartSelect #: PS1480658
Manufacturer #: WB01T10104
$8.08
  In Stock
HUB BLADE Assembly – Part Number: WB02T10289
HUB BLADE Assembly
PartSelect #: PS1020933
Manufacturer #: WB02T10289
$19.55
  In Stock
WASHER IGNITER – Part Number: WB02T10323
WASHER IGNITER
PartSelect #: PS1480698
Manufacturer #: WB02T10323
$8.08
  In Stock
INNER CAP BRASS – Part Number: WB16X32876
INNER CAP BRASS
PartSelect #: PS12709898
Manufacturer #: WB16X32876
$23.98
  In Stock
SCREW – Part Number: WB1X1261
SCREW
PartSelect #: PS234510
Manufacturer #: WB1X1261
$11.56
  In Stock
View More
Back to Top

Questions And Answers for ZDP304NT1SS

Be the first to ask our experts a question about this model!

Back to Top

Common Symptoms of the ZDP304NT1SS

[Viewing 7 of 7]
Little to no heat when baking
Fixed by
these parts
Fixing
Show All
Oven not heating evenly
Fixed by
these parts
Fixing
Show All
Oven is too hot
Fixed by
these parts
Fixing
Show All
Will Not Start
Fixed by
these parts
Fixing Fixing
Show All
Element will not heat
Fixed by
these parts
Fixing
Show All
Little to no heat when broiling
Fixed by
these parts
Fixing
Show All
Door won’t open or close
Fixed by
these parts
Fixing
Show All
Back to Top
Replacing the Temperature Sensor

Replacing the Temperature Sensor

View More
Back to Top
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven would go in to a F2 Error
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.
Parts Used:
Temperature Sensor
  • Peter from stamford, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
143 of 206 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't preheat above 300 degrees
Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.
Parts Used:
Temperature Sensor
  • Gerald from Cape Canaveral, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
48 of 78 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I kept getting An F2 error and the temperature did not seem accurate
1) pull out the stove
2) remove the 7 sheet metal screws holding the back panel on. (the panel that also covers where the cord splits and connects to the oven.
3) Find the small plastic connector located in the middle of the back of the range and unplug it.
4) open the front of the oven and remove the one screw holding in the oven temp sensor.
5) replace the sensor and make sure to "feed" the new cord through as best you can.
6) I had to dig through the insulation a little bit to find the new wiring harness
7) connect the wiring harness and put the back of the range back on

note: this was very simple to do if you think this might be the problem don't hesitate to handle this one yourself.
Read less
Parts Used:
Temperature Sensor
  • Chad from Bloomington, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable), Wrench set
27 of 34 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More
Back to Top