Models
>
ZDBC240NCBS
ZDBC240NCBS General Electric Wine and Beverage Cooler - Overview
Sections of the ZDBC240NCBS
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
SWITCH SPDT HIGH AMP
PartSelect #: PS1765837
Manufacturer #: WB24T10147
This light switch is controlled by opening and closing the oven door
$31.33
In Stock
Power Cord
PartSelect #: PS759476
Manufacturer #: WR23X10300
This heavy-duty cord has a three-pronged plug (2 electrical, 1 grounding). The power cord supplies power to your refrigerator, allowing it to keep the contents inside cool. There could be an issue wit...
$29.54
In Stock
Reverse Hinge Kit - Black
PartSelect #: PS758770
Manufacturer #: WR13X10275
This kit does not include the screws.
$119.81
On Order
R134 DRIER
PartSelect #: PS12727537
Manufacturer #: WR86X25269
The filter dryer filters refrigerant that travels through the sealed system of the refrigerator.
$62.27
In Stock
Questions And Answers for ZDBC240NCBS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the ZDBC240NCBS
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Convection oven fan and door light not working
The first step was to determine whether the problem was with the fan itself or the switch. I did this by opening the back cover and using a Volt meter to verify that the fan was not getting power. (I could have skipped this step.)
Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two he ... Read more x head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.
Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.
Next, I unplugged the range, closed up the back cover and lifted the range hood by removing two he ... Read more x head screws that are just inside and on either side of the top of the opening in the range door. Propping the hood open, I removed the connector leading to the switch, then pushed the switch out the front. Inspection showed that the switch was damaged so I closed up the range and ordered the part from Part Select. Once the part arrived, it was a 15 minute job to unplug the range, lift the top, install the new switch, and close up the unit.
Caution. On starting to install the switch, I failed to unplug the range and my finger brushed one of the hot contacts leading to the switch. Thankfully, I was not injured. Do not repeat my mistake on this issue. Unplug the range even if you're only installing this simple switch.
Read less
Parts Used:
-
Michael from Albuquerque, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
17 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt Smell
Unplugged the Range and removed the two screws holding down the cook top. You do not need to remove the vent chamber at the rear of the range since the top lifts up about 4 inches. This should be enough room to get your hand onto the plug going to the door switch. Pull off the plug and remove the swich. Pop in the new one, put on the
... Read more
plug, reinstall the two screws and you are done!
Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!
Read the thread on "burnt smell" and DO NOT assume it is a burned out element. Follow your nose!!
Read less
Parts Used:
-
Eugene from Hilton Head, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
8 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bar Fridge not cooling
Fridge stopped cooling. Opened back and could see fan running for coils but no sound from compressor. Other posts indicated this can be caused by bad capacitor compressor. Put fridge in Maint mode using front buttons inside on top. You can find maint mode instructions on internet. Used command to activate fans and compressor for 20 mins
... Read more
but still no compressor response. Ordered new Capacitor Compressor. It is hard to disconnect the old one, you have to open a plastic enclosure where all of the wires are connected into (not logic board, just some kind of master connection thing next to compressor). Brain surgery on that to get the red wire to unplug. Ended up breaking some plastic enclosure latches but don’t worry you can still put it back together. Ones red and blue wires are disconnected you can unscrew the old one and replace with new one. Suggest you take a few photos of how all the wires are connected so you don’t forget when putting back together. It fixed the issue and now old fridge is cooling like a champ.
Read less
Parts Used:
-
Craig from HIGHLAND, MD
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!