Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ZCG23SGSBSS

ZCG23SGSBSS General Electric Refrigerator - Overview

Get Parts and Repair Help for ZCG23SGSBSS

If you know the refrigerator repair part you need, you can browse the list of all parts on the ZCG23SGSBSS, or you can search by name or part description. You can also find your part by where it is located on the ZCG23SGSBSS by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ZCG23SGSBSS parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.98

Temperature Sensor

This temperature sensor, also known as a thermistor, is used for refrigerators and freezers. The sensor sends the temperature reading of the refrigerator towards the control board....

$12.74

Defrost Thermostat

This defrost termination thermostat acts as a safety device to stop the evaporator coil from overheating, by turning off the defrost heater at the end of the defrost cycle. The thermostat measures the temperature in your freezer to ensure that it stays at an optimum temperature to keep your frozen food from thawing. Some common symptoms linked to a faulty defrost termination thermostat include: the freezer is not defrosting, is too cold/too warm, or there is a frost build up in the freezer. Before you decide to replace this part, ensure that there is no frost build up in your freezer; as a build up can interfere with the thermostat reading.

$2.65

Evaporator Fan Grommet - Red

If you notice that your refrigerator or freezer is noisy or too warm, you may need to replace the evaporator fan grommet. This part is red in color, and is about 1 inch in diameter...

$63.92

Ice and Water Filter

This is an ice and water filter. The most common reason you would need to change this part is if you have never updated your model and it is no longer filtering your water. This also may lead to your refrigerator not dispensing water or ice properly. Manufacturers recommend you change your filter every six months to ensure it properly filters impurities. This will also ensure a normal dispensing rate. Note: As per the manufacturer, this is an updated water filter. If you have never installed the updated part or your old model was made by Culligan, you may need the adapter to install the filter. See Related Parts. Sold individually.

$7.36

Dispenser Door Assembly or Flapper

The dispenser door assembly (or flapper) is what opens to release the ice once the lever has been pressed. This part mounts in the ice dispenser. The cranker no longer comes with t...

$18.51

Module Shelf Insert

This part is located in the front of the module shelf.

$41.11

Dispenser Door Solenoid Assembly

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

$155.85

Ice Maker

This is a replacement ice maker kit, it is used in the freezer section of your refrigerator. This particular model will produce seven round or crescent shaped cubes every cycle. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level and ice is still not being made it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need. This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in connector, tube and fill cup. Before you start this repair, you should shut off the water supply and unplug your appliance. Please note, when you have installed your new ice maker it can take up to 24 hours for it to begin producing ice.

$41.22

Dispenser Auger

When activated, the auger rotates and pushes ice out of the bin through the chute to the user.

$3.37

Recess Door Spring

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Fridge too warm, evaporator icing up

  • Customer: Gerald from San Clemente, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 441 of 529 people found this instruction helpful
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wir... read more

flap to ice dispenser would not close

  • Customer: Bill from Cleveland Heights, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 380 of 438 people found this instruction helpful
The flap to the ice dispenser would not close, which allowed the ice dispenser to frost up, freezing the water dispenser.

This was a simple fix. The solenoid had stopped working, so it would not automatically close the door flap. I read some posts on this site that suggest that you had to remove the trim around the entire dispenser to get at the... read more

Freezer wouldn't maintain temperature ... got warm.

  • Customer: Mike from Scottsdale, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 229 of 276 people found this instruction helpful
The freezer in my side-by-side kept warming up -- often 20 degrees or more, which of course caused the fresh food side to warm up also. I do a lot of jump-in-with-both-feet home repairs, but never on a large appliance. Not having an ohmmeter, which cost about $100 for a reliable one, I took the symptoms to the internet. Countless self-help sites and U-Tube v... read more