Models > ZBD7100G02SS > Instructions

ZBD7100G02SS General Electric Dishwasher - Instructions

All installation instructions for ZBD7100G02SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ZBD7100G02SS
1-6 of 6
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

wire racks had rust on them

  • Customer: David from Collierville TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 2 of 6 people found this instruction helpful
they clip right into the lower rack. takes two minutes

water wouldn't drain out of dishwasher

  • Customer: Nicolette from Birmingham MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
I had pulled out the dishwasher. Pump was on the bottom. One screw and a clamp, pump was off. It went back together with ease. I am women.

Bad drain pump

  • Customer: Stephen from Olympia WA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 2 people found this instruction helpful
I chose to take the GE Profile SS dishwasher out on the porch for additional room to remove the bad drain pump. I ordered the wrong pump and while waiting a week for the replacement, the new great pyrenees puppy chewed the insulating blanket up. No worries I could tape it back together. When the new pump arrived I moved the washer into the kitchen for better light. It was then I saw the blanket was only eaten because the puppy had finished the chewing the wiring harness. All in all, the repair was easy and minus the time required to splice wires and replace connectors, it went very quickly.

Door seal kept popping out.

  • Customer: Michael from Portland AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 30 people found this instruction helpful
Removed door seal.

broken clip and broken silverware basket

  • Customer: Tammy from Franklin TN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replaced silverware basket and new clip. The clip was a bit tricky but I managed after a few minutes. Parts were correct and it's nice to have the dishwasher in good working order again!

water inlet valve leaking

  • Customer: Brad from wadsworth OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I had a shut off water supply shut off shut under my sink. That is where I shut the water off for the dishwasher. I knew it was for the dishwasher ,because it follow the line, and could see it was going to the washer. Then I went down stairs in the basement. Opened my breaker box, and found the breaker for the dish washer marked dish washer, and put in the off position. When I was still up stairs I opened dish washer , and inside at the top was two screws holding the dishwasher to the counter top. Those two screws turned out to be the exact size of just about every screw I ended up having to unscrew on this machine. So at the time I was in the basement turning off breaker, I went to the garage to gather up tools. Take the two screws that are screwed to the counter top. Then I layed on the floor, and at the bottom of the dish washer there is a panel on the front of the machine with screws attaching it. Take those screws out. Pull off cover. Now get a flash light so you can see. They're adjustable feet that the dishwasher are being leveled by. Those feet need to most likely be adjusted down so you can the machine pulled out, and make it possible to work on. now you can you can pull it out, but watch that water supply line does not get hung up, or electrical wires. Once the machine is pulled out there is another cover on the front that I took off. Four screws hold it on. Now you can get to the part to fix it. The other thing you need to know is after taking off the valve and taking off the old 90 fitting. It will need cleaned up. When you put it on the new shut off valve use pipe dope or thread tape so it doesn't leak. Good luck.
All Instructions for the ZBD7100G02SS
1-6 of 6