Models > ZBD6880K10SS > Instructions

ZBD6880K10SS General Electric Dishwasher - Instructions

All installation instructions for ZBD6880K10SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ZBD6880K10SS
271-285 of 288
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking from below

  • Customer: Craig from Massapequa Park NY
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
After determining that the leak was coming from the sump connector, I had to completely remove the unit from the counter. After removing all the parts in the wash cabinet (wash arms,conduit,fine,course and sump filters),the sump connector nut was revealed which I loosened, but did not remove, with a channel lock plier. The unit was then placed up-side down where I then loosened all the worm clamps that attached the drain motor,pump,and turbidity sensor to the sump and sump connector.then I removed the brackets that braced the pump to the washer body and removed the pump.at this point,you should be able to remove the drain motor and turbidity sensor from the sump and remove the sump from the washer. You should also be able to remove the connector as well.Both these items are made of some type of rubber which seems to deteriorate from the soap which was caked all over them in my case. Just reverse the above process to re-install everthing. I didn't find this job terribly difficult and it was certainly better than spending hundreds replacing the unit.

Rinse Dispenser Cap melted on heating coil

  • Customer: Martha from Kingman AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Opened dishwasher after it completed a wash cycle. Found the rinse dispenser cap had come off during the wash and melted on the heating coil at the bottom of the machine. Pulled cap off of coil, made sure coil was not disturbed. Looked in various sites for cap. Finally found this site where I didn't need to order the whole mechanism and could order just the cap. Received the cap, screwed into the dispenser, fixed. The only problem I had was that there were two possible caps so I picked the one that was the same color as the original one. Project completed. Thanks

Roller rusted off lower rack

  • Customer: Edward from Arlington VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed original rack, inserted replacement.

WEELLS BROCK

  • Customer: WARREN from JACKSONVILLE FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
REMOVED OLD WHEELLS REPLACED WITH NEW WHELLS.VERY EASY TO FIX. QUICKLY RECEIVED AFTER ORDER.

Lower Rack wheels "caving" in with any weight

  • Customer: Mary Lou from Rockford MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Nothing to replacing the wheels that flattened or totally came off with a full rack of dishes. I can't understand why I put off replacing them for SO long... found the replacement parts SO easily on PartsSelect website, ordered them late afternoon and they arrived a day later! YEAH! NO MORE CRASHING/FALLING DISH RACKS! Must say that I am totally unimpressed with the GE Profile Dishwasher but that's another story!

White stain on all dishes, glasses and plastics

  • Customer: Magdy from Saratoga Springs NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced motor and drain pump. Ealrier cleaned all parts from residue but did not help at all. Started to use Pre-wash powder for hard water after testing our water and found it at the acceptable high end. Getting excellent results now after repair.

Wheel on lower rack of dishwasher kept falling off

  • Customer: Dennis from Overland Park KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Bought new wheels & wheel axels. Very simple to replace (no tools required). New wheel axles much better desigh,

water leak

  • Customer: ronald from culver city CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Came home for lunch to discover the kitchen rug soaked and the dishes I had started when I left that morning unclean. Not sure what happened, pushed start again and immediately found water flowing out from under the machine. pulled the machine out and discovered that mice had chewed through the pliable vinyl sump tank. found the part number in my owners manual and google turned it up on Part Select. this was on Saturday and I had the part Tuesday. very satisfied

Lower rack wheels kept falling off

  • Customer: Benjamin from Carlisle PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After replacing the wheel and axle assembly once, I decided this time to instead just replace the axles with the new ones with improved design. Removed the wheels, pulled out the old axles and put the new ones in. Simple

The wheels were falling off the lower rack of the diswasher

  • Customer: Jeannette from Southgate KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Popped the wheels onto the wheel axle and let my 7 year old snap the completed assembly onto the lower rack. So easy, even a 7 year old could do it! Total cost of $28 to replace all 8 wheels, which had degraded over time. Lower rack now rolls in and out perfectly. The design for the replacement wheel axle is slightly different than the origional, so the suggested part is the right one, even though it looks a little different from what the dishwasher came with. I am now a happy girl and don't have to fight with my dishwasher any more!

HOLES IN SILVERWARE BASKET

  • Customer: James from Jefferson City MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
JUST PULLED OUT THE OLD BASKET AND PUT IN THE NEW ONE..DON'T KNOW THE HOLES GOT INTO THE BASKET...

Wheel axle broke

  • Customer: Kevin from Tacoma WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Get parts axles and wheels snapped together well.

small bearings came out and cap broke off the end

  • Customer: joe from parkland FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
put new part on by looking at other side no directions with parts

Broken wheel axel

  • Customer: Stephen from Irvine CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The rear wheel on the lower dish rack broke at the axle attachement. The wheel then feel inside the dishwasher against the heating element causing the wheel to melt. I ordered the new parts and they arrived very quickly. I attached the axle to the wheel with hand pressure, no tools required. I then attached the wheel assembly to the verticle support of the lower wash rack with hand pressure and was done. Very easy and the new design of the axle seems to attach better to the rack.

Wheels kept falling OFF

  • Customer: Darren from Northfield NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
The orginal axle design was terrible. The old axles broke and fall off. The new axles snap on with moderate force but the keep the wheels on now. The Rack works perfect now!
All Instructions for the ZBD6880K10SS
271-285 of 288