ZBD6800K00WW General Electric Dishwasher - Instructions

Took the bottom rack out and put axle and wheel on. Very simple to do. Took about 5 min. Would recommend this site to anyone. Thanks a bunch !

I was thrilled with the service. I received my package less than 24 hours after I placed my order. We removed what wheels were left and put the wheel axles on and then the wheels and it rolls beautifully now.

very easy, snapped in the axle and then clipped all 8 on the bottom rack of the dishwasher. Don't know why I waited so long to replace!

I had a small leak from under the dishwasher which turned out to be a tiny hole in the Pump Connector. With the power off I pulled the dishwasher out of the cabinet and disconnected the water and drain lines to give me more room. I put the dishwasher on its back to have access to the pump assembly. A couple of nut drivers and the pump connector is accessible. Replaced the pump connector and over tightened it "Crack"... had to replace the Main Conduit connector ($50). I was able to turn a simple $20 repair into a $70 repair. Now that's talent!

First I removed the excess water by using my shop-vac both inside the machine as well as near the bottom drain valve. After cleaning out that valve (which somehow had accumulated a pair of underwear) it was apparent that the drainage pump motor was no working (loud hum, not spinning). Replacement was easy, folowing instructions found everywhere on-line. Now the machine is working perfectly again.

Simply took out the broken rack and inserted the new one.

We googled, "thumping noise" when running the dishwasher and one of the possible reasons was the Lower Spray Arm. So, we purchased a new one and replaced it. Problem solved.

removed defective axel and wheels installed new ones

Replaced the part by taking off the srews on the inside of the dishwasher door (all of them)to get to the backside of the soap dispenser. Remove an electrical connector by pulling (had to pull off using pliers as it was really on there). Then a couple of screws hold to to the inside of the door. Pretty straight forward.

After determining that the leak was coming from the sump connector, I had to completely remove the unit from the counter. After removing all the parts in the wash cabinet (wash arms,conduit,fine,course and sump filters),the sump connector nut was revealed which I loosened, but did not remove, with a channel lock plier. The unit was then placed up-side down where I then loosened all the worm clamps that attached the drain motor,pump,and turbidity sensor to the sump and sump connector.then I removed the brackets that braced the pump to the washer body and removed the pump.at this point,you should be able to remove the drain motor and turbidity sensor from the sump and remove the sump from the washer. You should also be able to remove the connector as well.Both these items are made of some type of rubber which seems to deteriorate from the soap which was caked all over them in my case. Just reverse the above process to re-install everthing. I didn't find this job terribly difficult and it was certainly better than spending hundreds replacing the unit.

Installed new rack assembly and it works fine. Thanks

Opened dishwasher after it completed a wash cycle. Found the rinse dispenser cap had come off during the wash and melted on the heating coil at the bottom of the machine. Pulled cap off of coil, made sure coil was not disturbed. Looked in various sites for cap. Finally found this site where I didn't need to order the whole mechanism and could order just the cap. Received the cap, screwed into the dispenser, fixed. The only problem I had was that there were two possible caps so I picked the one that was the same color as the original one. Project completed. Thanks

removed original rack, inserted replacement.

Removed old wheells replaced with new whells. Very easy to fix. Quickly received after order.

Nothing to replacing the wheels that flattened or totally came off with a full rack of dishes. I can't understand why I put off replacing them for SO long... found the replacement parts SO easily on PartsSelect website, ordered them late afternoon and they arrived a day later! YEAH! NO MORE CRASHING/FALLING DISH RACKS! Must say that I am totally unimpressed with the GE Profile Dishwasher but that's another story!