YWGD5300VW1 Whirlpool Dryer - Instructions

Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.

Man o man...please listen up. Would not start..replaced the thermal fuse was the first step I took according to web sight...started right up... Then it took 2 cycles to dry clothes..I went down the recommendations from the highest. % to the lowest %..replaced. over 80$ in parts..cleaned out all vents..from lint ext...still would not work..then come to find out my kids jammed a small toy in the exhaust flap on the outside of the house..the flap stayed closed when the dryer was running..there was no place for hot air to go but back in the dryer..and it seemed to run fine..but the sensors were cutting off the heat early...lesson learned..do not buy any parts until u clean all lint parts..vents..and make sure there are no obstructions with air flow..other wise this is the best place to buy parts..period..

just replaced the rollers with the new ones. The trouble was getting the belt around the drum again, but it all worked out and the dryer is running good

The repair went very smooth. I was able to follow the directions on partselect and had the repair done in 15 minutes. I took extra time to test the continuity on the ignitor and fuses. I also used the shop vac to clean out the inside of the dryer. The best part I liked about this web-site is the fact that once I described the problem I was told that the "M" series style coil was the fix 90% of the time! $27.70 including shipping was all it cost to make my clothes dryer work like it did the first day we got it!!

Wouldn't have had a clue how to gain access to the coils without online instructions. It actually took longer to open the front of the unit than it did to replace the parts. Following the online instructions I removed two screws under the lint trap door. I then used a stiff putty knife under the left and right front corners of the lid to release the top, which I tilted back. Per the instructions I easily located the two screws releasing the front of the dryer. You have to lift the drum a bit to release the front panel. Once removed I was able to remove and replace the failing coils and then reversing the steps to put it all back together. An easy job and the dryer is back in shape.

Replaced Thermal Fuse

Your website was wonderful--thank you so much! When I saw that 47% of the time this was the problem, I ordered it & it worked! This was a life saver for me! I will come back to this site anytime I have an appliance problem! Thanks again!

All went very easily

unscrewed the 2 screws holding the coil's in place took wires off one coil at a time tested coils with ohm meter found the two wire coil was bad replaced and scered the bracket that holds the coils back in place.PartSelect gave me a list of what was causing the problem and what the % of what was the cause,this helped alot Thankyou PartSelect

took the top and front off the dryer and had to route the new belt around the drum and through the pulleys, it was really easy and a heck of a lot cheaper then buying a new dryer

Called PartSelect, gave them the make and model number of the dryer and told them I needed a new belt for it. They gave me a price including shipment (under $20.00). I oreder the new belt and it arrived within a week. I also got an e-mail from PartSelect with a video showing how to replace the belt. This was very helpful. I was able to watch the video, take the dryer apart, replace the belt (after a few tries), and put the dryer back together. Problem solved! Thanks PartSelect.

very easy had to do some rewirng.who ever had it before me bypassed the fuse and several other things.

Just like the video. Disconnect the lint shute. Pop the top lose. Disconnect the door switch. I actually took the hooks off an removed the entire lid. Took the two screws out and removed the front panel. (The OEM idler was a teflon half-moon so I think the abrasion was what caused the belt to fail.) Put the belt around the drum. Rolled the drum to check the seal overlap was proper. Installed the idler and wrapped the belt around the motor shaft. Put it back together. Would have been a little easier with a helper.

Folowed the tips that I got with the part and on the site. Could not have been an easier way to save about $150 in a pro service call and marked up price for their part. Very easy install. Drying working as it should. Now, I just learned the washer control mechanism is about to go bad, so ill be back for that part too. Thanks.

Found an instructional, easy to follow video by PartSelect online. It was helpful to know what tools I needed before beginning the job. I first purchased only the belt. After taking the dryer apart, I saw the idler had also broke. It was very helpful that the parts arrived quickly. The video was the the greatest tool for doing this repair myself!!!!