YWGD5300VW0 Whirlpool Dryer - Instructions

the ignitor did not glow red checked thermal fuse by exhaust duct. fuse open replaced thermal fuse

Took off the top and front panel. Found that the belt tensioner was worn out. Decided to pull drum out,and replace the belt and drum rollers also. Put it back together, and it works fine.

I wasn't sure if the problem was the belt (probable) or the idler pulley assembly (less likely) but the total for both parts was about $26 plus shipping. So why not replace both to be sure?

As it turns out, my original idler pulley assembly does not turn. Rather, it has a concave semi-circular piece that is fixed in place. The belt ran in a groove in that piece.

The replacement part has a nylon wheel that turns. As a result of replacing the idler pulley assembly (which I don't think was necessary to fix my tumbling problem) the dryer runs much quieter. (We used to get a fair amount of squeaking when the belt rubbed).

As for the actual repair (I would rate myself as above average on tackling household repairs), it was about the simplest repair I've ever done. I followed the video provided on this site (excellent video) and it took less than 20 minutes -- cleaning up all of the lint/odds and ends under the washer and dryer took longer than the actual repair.

My only issue (minor) was disconnecting the electric harness. It did not slide as easily as in the video. I had to coax mine a bit with a small screwdriver (make sure your dryer is unplugged!!). I suspect it was simply a function of the harness never being unplugged -- the dryer is 9 years old.

I also felt great because I'm sure I saved a $125 service call (for only $26 in parts and 20 minutes of my life).

Good luck!

Received conversion kit. Removed front dryer panel,2 screws. Removed burner tube, 2 screws then removed natural gas orfice.
Installed propane orfice and repalced burner tube.
Removed regulater plug and replaced with new plug from kit using 90 degree ratchet screw driver. Approximately 20 minutes. Dryer working great.

Followed your online video for disassembly and it was not only educational but actually quite simple. I would recommend that you start the video with," make sure the power cord is disconnected from the power source". I have worked on numerous pieces of large electrical equipment and would strongly suggest this be added. Some people think if it's, "off", it's safe. Your phone staff when ordering was great. We will do business again.

My wife reported that the dryer was not working. I checked it and it seemed to work fine. This went on for about a month or two. Every time I checked it, it started just fine.

Well, she threatened to go buy a new dryer, I took her more seriously. I thought perhaps a thermal protection was the cause. But when I dug into it, I learned that when those trip out, they are permanent (have to be replaced).

I finally noticed loud humming sound the motor made at start-up, when it failed to start turning on one occasion and eventually tripped out the motors thermal protection.

I ordered the new drive motor form PartSelect.com.

Replacing the motor was fairly easy if you like to take stuff apart. One thing that I had not anticipated was that the two foam gaskets on the exhaust duct were dry rotted. I went to my local part supplier to get them. They did not have them in stock. :( While I was there, I asked how much the motor was, they wanted $50 more than PartSelect.com :D

I put it back together without the new gaskets, and it runs like new. I ordered the gaskets from PartSelect and will add them when they arrive.

My wife is happy again, she can bust out the laundry in one day; it had been taking here all weekend.

I learned to take her at her word.

I opened the panel, undid the plugs, detached the radiant sensor by undoing one screw and removed and replaced the part. Fairly simply.

I analyzed the situation to see how to remove the old lint screen. I carefully pulled out the old lint screen. I was careful not to drop it. With caution, I placed the old lint screen in the trash receptacle that was nearby. Next, I opened the box that the new lint screen came in with a sharp knife. I removed the new lint screen from the box, took off the plastic wrap and inserted the lint screen in the same slot that the old one used to be in. I tested that it was seated correctly by pulling it out and reseating it in the slot. The true test came when I ran my first load of laundry through the dryer. The total repair time for this fix was 14.92 seconds.

the problem was not the igniter its was the thermal fuse I broke the igniter during inspection of the problem be careful its a very easy thing to break repairs complete thank you parts select for the quick shipping and low prices

Replaced the belt and the wheels supplied with the kit. I also cleaned the inside of the unit. It looks and works like new.

**** Remove power cord from the wall****

As said earlier, you will need to lift the top. Drop the two screws holding the lint shoot and pop the top by sliding a screw driver into the corner on the front. Lif tthe top and rest against the wall behid the unit. remove the two (4 total) screws at the top and bottom of the front door assembly.
Place sometin under the front portion of the drum. At this point you'll see the need to clean everything! :) Slide the belt off and around the drum, (take note of the routing it takes.) Remove the drum by gently pulling it towards you. Set it aside. Clean more. :) (It is nice to have a vacuum handy.) At this point you really need to get to the rear of the system. So I tipped the top back down, and spun it around. Removed the rear panel and cleaned some more. (15 years of a lot of lint in there!) Then you'll need to remove the rear cover on the left side, covering the blower impeller. Get read for a whole lot of debris. Vacuum again. So now you have the motor exposed in the front and rear. You need to remove the impeller by turning that clockwise to loosen it. The trick is holding the shaft in place from the front at the same time. I used an old rag and wedged it into the impeller edges and worked it around until it jamed up. Once the rag was wedged pretty good, I went back to the front spun the shaft. Then you can remove the impeller by hand. Vacuum more. You may get by without having to remove the lint shoot completely, but I did just to clean it up more. I did have to remove two screws in the upper corner near the top of the lint shoot. (Basically the hold the back in place.) I took a few notes at this point about the wiring harness. Used a heavier screw driver (standard), You can push down on the clips that hold the old motor in place. Then work it out the front. Clean more. The new motor is not an exact replacement slightly differnt but the instructions with it were ok. Follow them for the correct wiring. You will need to remove one wire and cut and recrimp a spade lug or two. I used ty-wraps to secure the lines back in place. Look closely at the diagrams and make sure you set the motor down in the same direction the instructions say, if you twist it slightly it will sorta lock in place where it needs to be. Re-install the hold down clips to the front and rear of the motor. Clean up your impeller, and reinstall it too. Then basically reassemble the dryer...tracing your steps backwards. This isn't really difficult, it just takes time and as you can see, you will/should clean as you go !

Took the back off the dryer control panel, unscrewed the old timer, unplugged the wire leads from the old timer and put them on the new timer. Then I screwed the new timer in place of the old one and replaced the back panel cover. one nut driver did the whole repair. about ten minutes tops.

Once the coils for the gas valve got hot they failed and shut the gas vavle off, we ended up changing the coils which fixed the problem but part select held up there end of shipping out these parts which we could not get localy. so if your dry ignites some time and or not for long its either these coils or the cycling thermostat which will casue the same conditions because the the cycling thermostat controls the coil. good luck!

Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open). Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.

Problem: Drum light not working, bulb ok. Removed 6 screws on panel behind timer, light, buzzer, switches. Lifted back of dryer top then moved dryer top forward and off of dryer. The switch was located above the door. Unhooked wiring plug and took out 2 screws holding in the switch. Installed new switch and repaced bulb. Reassembled as needed and tested light by opening door. Works great.