Models > YWED6200SW1

YWED6200SW1 Whirlpool Dryer - Overview

Get Parts and Repair Help for YWED6200SW1

If you know the dryer repair part you need, you can browse the list of all parts on the YWED6200SW1, or you can search by name or part description. You can also find your part by where it is located on the YWED6200SW1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for YWED6200SW1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.11

Thermal Fuse

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins...

Order within the next 3 hrs and your part ships today!
$28.84

Thermal Cut-Off Kit

This clothes dryer thermal cut-off kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires.

Order within the next 3 hrs and your part ships today!
$33.43

Maintenance Kit

NOTE: This kit is for 29" wide dryers built 1965 or later. Please verify model # before ordering as may not work for all models. This kit comes with one multi-rib belt, two drum ...

Order within the next 3 hrs and your part ships today!
$3.69

Door Catch

This part helps to keep the door closed when the machine is in use.

Order within the next 3 hrs and your part ships today!
$10.71

Drum Support Roller

Sold Individually. Most dryers require 2. Tri-rings sold separately.

Order within the next 3 hrs and your part ships today!
$20.21

Internal-Bias Thermistor

Part may differ in appearance, but functions the same as original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

Order within the next 3 hrs and your part ships today!
$4.54

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Order within the next 3 hrs and your part ships today!
$3.54

Leveling Foot

Sold individually.

Order within the next 3 hrs and your part ships today!
$5.62

Tri Ring

Sold individually.

Order within the next 3 hrs and your part ships today!
$36.73

Lint Filter

Also known as Lint Screen. Handle is white in color.

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1311 of 1500 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

No Heat

  • Customer: Vernon from Niceville FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 581 of 599 people found this instruction helpful
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off. read more

No heat but would run otherwise

  • Customer: Dana from Grassvally CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 529 of 543 people found this instruction helpful
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and didn't take but 15-20 m... read more