Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YSF315PEPQ1

YSF315PEPQ1 Whirlpool Range - Overview

Get Parts and Repair Help for YSF315PEPQ1

If you know the range repair part you need, you can browse the list of all parts on the YSF315PEPQ1, or you can search by name or part description. You can also find your part by where it is located on the YSF315PEPQ1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for YSF315PEPQ1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$3.02

Screw

This screw is sold individually.

$71.80

Oven Sensor

This oven temperature sensor, for ranges, works together with the oven control board to measure and regulate the oven temperature. The sensor detects the temperature in the oven ca...

$12.40

Burner Knob

This white knob take a D-shaped shaft. Sold individually.

$6.36

Touch-Up Paint - White

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, ...

$24.90

Lower Door Trim

Sold individually.

$18.26

Front Foot

This adjustable front leveling foot is sold individually.

$7.83

Rear Leveling Leg

Sold individually.

$3.19

Screw (4)

Sold Individually.

$11.51

Spray Paint - 12 oz. - White

Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a protective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

our oven would not heat up

  • Customer: sharnette from baltimore, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 72 of 78 people found this instruction helpful
My husband pulled out the stove turned the gas off then he pulled out the part and replaced igniter....it took only about 20 min to do this job it was very easy and prior to us doing ourselves i called a well known company that does home repairs, I also called a few smaller businesses and to replace this part was anywhere from $175- 250 if not more. we are v... read more

temperature not accurate after 3 1/2 years of happy usage

  • Customer: Ruth from Oregon, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 99 of 173 people found this instruction helpful
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.

The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I tur... read more

Oven stuck in cleaning mode

  • Customer: Hal from Santa Rosa, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 40 of 76 people found this instruction helpful
Google the error code that the range was displaying and found others with the same symptoms. Then found several people that had fixed the problem by replacing the oven sensor. I then ordered the sensor and replaced it, which fixed the problem. read more