Models > YSF315PEGW6

YSF315PEGW6 Whirlpool Range - Overview

Get Parts and Repair Help for YSF315PEGW6

If you know the range repair part you need, you can browse the list of all parts on the YSF315PEGW6, or you can search by name or part description. You can also find your part by where it is located on the YSF315PEGW6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for YSF315PEGW6 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.58

Light Bulb - 40W

Sold individually.

Order within the next 6 hrs and your part ships today!
$11.51

Control Knob

This knob accepts a D-shaped shaft. Sold individually.

Order within the next 6 hrs and your part ships today!
$2.70

Torx Screw

7-18 x 3/4" - sold individually.

Order within the next 6 hrs and your part ships today!
$13.33

Control Knob

This knob accepts a D-shaped shaft. Sold individually.

Order within the next 6 hrs and your part ships today!
$2.70

Screw

This screw is sold individually.

Order within the next 6 hrs and your part ships today!
$13.29

Surface Burner Spark Igniter

This part helps your burner ignite and produce flame.

Order within the next 6 hrs and your part ships today!
$67.62

Sensor

This temperature sensor detects the temperature within the oven cavity.

Order within the next 6 hrs and your part ships today!
$39.84

Oven Rack

Sold individually.

Order within the next 6 hrs and your part ships today!
$2.70

SCREW

This screw is sold individually.

Order within the next 6 hrs and your part ships today!
$2.70

Igniter Screw

This screw is sold individually.

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

temperature not accurate after 3 1/2 years of happy usage

  • Customer: Ruth from Oregon IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 63 of 119 people found this instruction helpful
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.

The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I tur... read more

The (relatively new) gas oven would not light...oddly enough after a power outage. The recommended typical troubleshooting experience was that if the oven will not light: replace the igniter, even if it appears to be working fine.

  • Customer: Robert from Sun City CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 26 of 28 people found this instruction helpful
I had already removed the 2 plates in the bottom of the oven to take an initial look. After not finding anything obvious, and searching on line for advice, I ordered the igniter. After the igniter arrived it was a matter of removing 2 screws, pulling out the lower drawer to gain access to the igniter disconnect, and done.

thanks for getting the ... read more

mice had made nests in the insulation wrap in the range

  • Customer: Wendy from Red Hook NY
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 18 of 18 people found this instruction helpful
I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told m... read more