Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YSF315PEGQ6

YSF315PEGQ6 Whirlpool Range - Overview

Get Parts and Repair Help for YSF315PEGQ6

If you know the range repair part you need, you can browse the list of all parts on the YSF315PEGQ6, or you can search by name or part description. You can also find your part by where it is located on the YSF315PEGQ6 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for YSF315PEGQ6 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

Order within the next 12 hrs and your part ships today!
$5.15

SCREW

Sold individually.

Order within the next 12 hrs and your part ships today!
$7.22

Touch-Up Paint - White

18ml

Order within the next 12 hrs and your part ships today!
$35.96

Oven Door Trim Kit

This white oven door trim set contains three pieces: two for the sides of the door and one for the bottom. The screws are sold separately.

Order within the next 12 hrs and your part ships today!
$38.91

Door Trim Kit - Black

This kit includes the 2 side pieces and 1 bottom piece. NOTE: This kit has been updated by the manufacturer. The lower screws are no longer needed for the side trim now locks in to...

Order within the next 12 hrs and your part ships today!
$11.07

Spray Paint - 12 oz. - White

Order within the next 12 hrs and your part ships today!
$49.47

Top Trim

Black in color.

Order within the next 12 hrs and your part ships today!
$12.31

Anti-Tip Bracket Kit

This kit keeps your appliance from tipping. Comes with bracket, ring and 2 screws.

Order within the next 12 hrs and your part ships today!
$7.11

Hinge Pin Kit

Includes 4 hinge pins. Used at hinges to hold door open so the door can be lifted off.

Order within the next 12 hrs and your part ships today!
$20.80

Spray Paint - Surperior Black

This is a 12oz can of black spray paint.

Order within the next 12 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

temperature not accurate after 3 1/2 years of happy usage

  • Customer: Ruth from Oregon, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 82 of 146 people found this instruction helpful
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.

The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I tur... read more

The (relatively new) gas oven would not light...oddly enough after a power outage. The recommended typical troubleshooting experience was that if the oven will not light: replace the igniter, even if it appears to be working fine.

  • Customer: Robert from Sun City, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 26 of 28 people found this instruction helpful
I had already removed the 2 plates in the bottom of the oven to take an initial look. After not finding anything obvious, and searching on line for advice, I ordered the igniter. After the igniter arrived it was a matter of removing 2 screws, pulling out the lower drawer to gain access to the igniter disconnect, and done.

thanks for getting the ... read more

Socket Light had a bad thread

  • Customer: Edmund from Emporium, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 29 of 39 people found this instruction helpful
Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cover read more