Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YRBS305PDS9 > Instructions

YRBS305PDS9 Whirlpool Wall Oven - Instructions

All installation instructions for YRBS305PDS9 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the YRBS305PDS9
1-15 of 120
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broke the glass panel inside the oven door -- dropped a baking dish on the glass!

  • Customer: Robert from Wildwood, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 139 of 175 people found this instruction helpful
Easily removed the door from the oven by releasing clips attached to the door hinge -- very nicely engineered. Removed about 6 philips head screws to allow the door assembly to be taken apart for access to the glass. Lifted out the broken glass, cleaned the inside of the door, installed the new glass, reassembled the door (a two minute project), and reattached the door to the oven. Cleaning the inside of the door took longer than the actual repair!

No heat after cleaning oven

  • Customer: Frederick from St. Louis, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 87 of 96 people found this instruction helpful
This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your power cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.

Cracked the inner door glass by wiping with wet rag when hot

  • Customer: James from Renton, WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 41 of 48 people found this instruction helpful
Removed the oven door by following the straightforward instructions in the user's manual. Removed philips head screws to take the door assembly apart. Removed clips holding the two inner door glass plates, and the two plates. Removed the clamp holding the broken glass plate, then the glass and associated glass fragments. Then cleaned and re-installed the three glass plates and their clamps in reverse order. Re-assembled the door and re-attached to the oven. Only cautionary note is to be careful when removing, handling and re-installing the various glass plates. Watch out for fragments from the broken plate; they can cut you and/or fall on the floor.

I broke the Bake Element while cleaning the oven.

  • Customer: Daniel from Cheraw, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 40 of 49 people found this instruction helpful
I removed the two screws that held the bake element in place. Next I removed the Bake Element. I had to unscrew the oven to go behind it because when one piece off of the element broke, it slide back behind the oven. I pushed the wire back thru the piece holes, connected the Element, and pushed the element with the wires back through the holes. I rescrewed the element in place and the oven. PartSelect helped me to save this year's Christmas.

Oven wouldn't heat after cleaning cycle

  • Customer: Devin from Platte City, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 25 of 26 people found this instruction helpful
Turned power to oven off. Removed trim screws and trim. Removed screws that anchored oven in cabinet. Removed oven from cabinet. Removed back panel, tested thermal fuse. Determined it was defective, ordered new part and reversed procedures above to reinstall.

Bottom Oven Element Wasn't Working

  • Customer: Shannon from Carlsbad, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 24 of 25 people found this instruction helpful
It was easy to remove the old element. It only required the removal of two screws and pulling apart the electric connectors. It was just as simple to install the new one.

cracked iner door glass

  • Customer: william from albuquerque, NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 23 of 29 people found this instruction helpful
Important note: hinges are left and right do not mix them up or door will not re-assemble properly and you'll get to do it twice.

Steps I took:

Removed the oven door per the instructions in the oven operator manual. Removed several screws to release the interior steel liner.

Removing the steel liner was a bit of a hassle, Had to manipulate it to get it loose but it eventually came away from the stainless steel exterior door panel.

Disassembled the interior glass layers, there are three. The glass you need to replace is the last layer, of course. removed and discarded the broken glass. Note: the interior glass is not secured by a bracket or screws, it is held in place by compression of the interior steel liner and a another liner that is inside the door assembly (you'll figure this out when you dis-assemble).

Another note: there is a fluffy material gasket between these two liners, use care when you disassemble or the fluffy gasket will turn into confetti.

Take the opportunity to clean all glass and parts of the accumulated oven grease.

Re-assembled door and re-installed...looks good.

Another note, getting the door back together requires a little patience because there are clamping overlaps of the steel liner to the SS exterior door panel. Be prepared to jockey things around a little and make sure all your screw holes are all lined up before you begin to button it up. Remember, hinges are left and right they are not interchangeable.

Replacing Top Oven Inner Glass Door

  • Customer: Melissa from Stockton, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 27 of 43 people found this instruction helpful
We had to remove two screws from the bottom of the outer glass door that held two brackets. Those brackets held the glass door in place. Then we had to remove two more layers of glass after that using a screwdriver. Then the inner glass, which was the one broken, we had to use pliers to bend the metal tabs that were holding it in place. We got the new glass in, bent the metal tabs back, returned the other two layers of glass, and then slide the outside glass door back in and returned the two brackets at the bottom. The hardest part was figuring out how to get started. Once we removed those bottom brackets, it was pretty easy after that.

al 4 interior lights had burned out

  • Customer: Kimberlee from Rocklin, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 22 of 30 people found this instruction helpful
The glass caps that cover the bulbs screw out by hand. Then, it was just like changing any other light bulb. I put the caps back on, and magically, we could once again see our food cooking. We had asked other repair companies to replace the bulbs when we had other major work done, but they either didn't want to take the time to get a part number, or didn't want to get it for us. On the PartSelect website, it was easy for us to find and order, not to mention we saved at least $75.00 on the service call alone. Thanks PartSelect!

Original oven gasket had discolored and deteriated, mainly due to use of oven cleaner.

  • Customer: Ralph from Green Bay, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 19 of 23 people found this instruction helpful
I removed the bottom gasket retainer , single screw, with a screwdriver. The old gasket just pulls away. I cleaned the area under the old gasket with soap and water. I installed the new gasket whcih easily slips in place with the already installed retainer wires into the pre drilled holes.

Viola. Lokks like new.

Scratches in Surface

  • Customer: Michelle from Richardson, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 20 of 29 people found this instruction helpful
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Bake Unit not heating properly

  • Customer: Dan from Madison, MS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 17 of 21 people found this instruction helpful
Turned the power to the oven off. Took two crews out. Disconnected the old unit, connected the new unit, put the two screws back in and tested the unit.

Broken Inner door glass

  • Customer: omar from fontana, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 28 of 56 people found this instruction helpful
I went online to read the instruction. Started doing it and was done in less than 30minutes. It was easy and the replacement part was inexpensive and got shipped in really fast. I probably would have spent hundreds of dollars if i called a handy man to repair it. THANK YOU VERY MUCH.

Door was accidentally broken by 5 year old child

  • Customer: Leonard from Auburn, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 18 of 27 people found this instruction helpful
Just removed two screws that held the top brackets on, and cleaned out the old broken glass. When the part came it, installed the two top brackets to the glass and then slide the glass into the two bottom brackets and screwed the top brackets in place. Whole job took about 20 minutes.

Oven wouldn't heat after a cleaning cycle

  • Customer: Robert from Willow Park, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 16 of 21 people found this instruction helpful
Recieved the part promptly. From looking at the diagrams, we knew the overload thermostat was located on the back of the oven. We removed the screws, brackets, etc, slid the oven out, which for us was fairly easy as it's an under counter oven. Located the thermostat, removed it, replaced the new one, connected two clip wires, replaced the oven, turned the power back on and it works like a champ. Total cost was under 50 bucks.
All Instructions for the YRBS305PDS9
1-15 of 120