YMET3800TW1 Washer Dryer Combo - Instructions

Pop cap off top of agitator. remove bolt that holds down agitator,which lets you remove the top of agitator that holds the directional cogs. remove top install cogs, make sure they are turned in right direction, and re install top of agitator.

I followed exactly the video. It really was that simple. My 5 year old even helped me unscrew the nuts. The Thermostat was on the lint shaft and unscrewed easily. Once out I removed the wires. The hardest part was removing the wires, They were really tight. I replaced the wires and screwed in the part. Before I replaced the back I cleaned out the lint tube and turned on the dryer. I saw the flame and the heater kicked right on. I replaced the back and was done. *****However the next time the dryer went the heat didn't remain on and turned off too soon. I did some more research and found you usually need to replace the thermal fuse at the same time on Whirlpool units. So I have ordered the part and will let you know if kept the heater from turning off too soon.

Ordered part ( door latch ) flowed instructions easily fixed same.

(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.

as in video

After about 4-5 years, the agitator cogs or "dogs" will wear out and cause the agitator to stop working-Simply pop the cap off of the top of the agitator with your hands by pulling upwards, remove the plastic cap at the bottom of the agitator-there are 2 plastic ears that you pull up on also with your hand, exposing a 1/2 locking nut. Use a socket and extention to unscrew the nut. Grab the bottom of the agitator with both hands and pull sharply upwards removing the entire assembly. Flip the assembly over to expose the four cogs. Replace with new, and reverse the procedure to reinstall the agitator

im a car mecanic it was easy

It snapped right in. Works perfect.

Thanks to the video, this repair went very easy and quickly, the part arrived earlier than stated, my whole experiance with PartSelect from ordering to installing was fantastic, THANK'S

Parts Select is AMAZING!! It directed us to the correct parts. Ordering was easy. But the best part was the videos. The step by step instruction was a godsend. We followed it, paused it, compared it, did it. We had to battle grease and tight quarters, but got it done. The machine works good. We spent about $65 as opposed to $400+ for a new washer. Great website.

When my 13 yr old washer stopped working the timing was not at all good to spend money on a new one. I have two of my children getting marriied within the next year and funds are tight. I decided to troubleshoot it myself online by googling my problem. I found out what I thought would be the parts I needed, I took a chance and ordered them. The bonus was the videos that you emailed me with the complete installation instructions. I am a banker and a 53 yr old woman ...not exactly a handy man. With your videos I was able to fix my washer by my self for just the cost of parts...so my wedding budget is still in place. I highly reccommend PartSelect for anyone...cause If I can do it anyone can do it! Thank you PartSelect

very easy and the exact problem Thanks.

I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.

Easy as 123... unscrewed the top agitator, removed the parts and replaced. This part cost me about $3.00 and the repair call the last time was $250.00. I guess I would call it a profitable day!

I actually thought the job of replacing the clutch was more difficult than it actually was. I simply watched the video on how to do it and it was really a task that pretty much anyone could do. The only bit of trouble I had was putting the C-shaped wire clip back on the shaft to hold the clutch in place......other than that everything else was pretty easy.....I would definately use Partselect again...