Models > YMET3800TW0 Whirlpool

YMET3800TW0 Maytag Washer / Dryer Combo - Overview

Get Parts and Repair Help for YMET3800TW0

If you know the washer / dryer combo repair part you need, you can browse the list of all parts on the YMET3800TW0, or you can search by name or part description. You can also find your part by where it is located on the YMET3800TW0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer / dryer combo. We’ve also included any installation videos we have for YMET3800TW0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.46

Agitator Directional Cogs

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

$20.99

Direct Drive Motor Coupling

This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.

$14.60

Cycling Thermostat

Cycling thermostats continually cycle the heating element off and on to maintain a constant inner temperature. This particular cycling thermostat has a limit of 155 degrees Fahrenh...

$4.76

Door Catch Kit

This dryer door latch kit comes with one plastic door latch and one metal door strike.

$2.67

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

$43.96

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring for compact washers. As per factory, the green spring (1.24") replaces the black spring (1.46").

$13.86

Idler Pulley with Tri-Ring and Gasket

A dryer's idler pulley helps the belt to rotate the drum. Also known as dryer belt tension pulley wheel.

$25.02

Thermal Cut-Off Kit

This kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse with a limit of 360 degrees Fahrenheit. The thermostat and fuse help prevent the dryer from overheating.

$17.28

Multi Rib Belt

This dryer drum belt from Whirlpool/Kenmore has five ridges. It is used for many of Whirlpool's brands of clothes dryers. This flat belt is 1/4 of an inch wide.

$10.77

Door Catch Kit

This kit comes in two pieces: the catch and the clip.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No movement from Basket & agitator

  • Customer: Jeff from Wayne NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 412 of 438 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

top half of agitator did not move during wash cycle

  • Customer: dennis from new stanton PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 168 of 190 people found this instruction helpful
pull off softner dispenser, pop off agitator cap by inserting straight screw driver into small slot, remove bolt inside agitator with socket wrench and long extension, pull agitator straight up off shaft, place agitator on floor, with feet holding bottom half pull top half apart from bottom half by pulling straight up, note direction of old cogs remove and r... read more

spin cycle did not engage

  • Customer: Andrew from SLC UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 156 of 168 people found this instruction helpful
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase... read more