Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YMED9600SQ0 Maytag

YMED9600SQ0 Maytag Dryer - Overview

Get Parts and Repair Help for YMED9600SQ0

If you know the dryer repair part you need, you can browse the list of all parts on the YMED9600SQ0, or you can search by name or part description. You can also find your part by where it is located on the YMED9600SQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for YMED9600SQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$26.37

Lint Filter

This filter collects lint as it passes through the dryer vent.

Order within the next 29 mins and your part ships today!
$20.82

Idler Pulley

The idler pulley with tri-ring and gasket, also known as a dryer belt tension pulley wheel, is used in dryers. This part maintains the right amount of tension for the belt to rotate the drum. This effectively spins the drum. If your dryer is experiencing any of the following symptoms, it is best to replace this part: not rotating, does not start, making squealing noises when it is in use, or it does not tumble properly. For this repair project, the tools needed are a Phillips screwdriver, 1/4 inch nut driver, putty knife, small flat blade screw driver, and needle nose pliers. Refer to the manual provided by the manufacturer for installation instructions.

Order within the next 29 mins and your part ships today!
$50.13

Heating Element - 240V 5200W

This heating element fits later model electric clothes dryers and has 5/16" terminals.

Order within the next 29 mins and your part ships today!
$13.09

Drive Belt

This dryer drum belt has 4 ribs and 3 grooves. This belt is 1/4 of an inch wide.

Order within the next 29 mins and your part ships today!
$21.40

Thermostat, Internal-Bias

Part may differ in appearance, but functions the same as original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

Order within the next 29 mins and your part ships today!
$5.77

Tri Ring

If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.

Order within the next 29 mins and your part ships today!
$5.00

Heating Element Connection Wire Kit

This kit is used for electric clothes dryers, and it comes with a yellow wire nut.

Order within the next 29 mins and your part ships today!
$44.33

High Limit Thermostat and Thermal Fuse Kit

Also known as Thermal Cut-Off kit. The thermostat acts as a safety mechanism that keeps the dryer from overheating and the fuse is like a backup system - it's set to trip at a higher temperature than the thermostat. Once it trips, it has to be replaced.

Order within the next 29 mins and your part ships today!
$5.84

Leveling Foot

If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs...

Order within the next 29 mins and your part ships today!
$4.63

Washer, Thrust

This genuine OEM washer has a 3/4 inch outside diameter. This thrust washer can be used on most makes and models of dryers. A complete list of compatible dryers is available below. The washer is found on dryers around the drum support rollers and idler pulleys, and helps prevent the rollers and pulleys from bumping up against the brackets they are installed on. Your thrust washer could be defective if you notice your dryer wont tumble, rotate, or turn; or there is a load squealing or whining noise when the dryer tumbles. The repair is a relatively easy job. You will require a putty knife, 5/16 inch nut driver, and E-Ring pliers. Remember to disconnect the power to your dryer before you begin the repair.

Order within the next 29 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Burned out heater element

  • Customer: Alan from Brooksville, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 389 of 434 people found this instruction helpful
Remove the kick plate from the bottom of the dryer by sliding a putty knife along the top edge to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the heat shield on the right, held in by one hex head screw. Remove screw and heat shield. The element is positioned in an open-front housing... read more

felt strip came off lint screen

  • Customer: JEFFREY from FALL RIVER, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 192 of 230 people found this instruction helpful
ordered new lint screen, removed old screen, inserted new screen. read more

catch mounted on door broke

  • Customer: Paul from Mt. Pleasant, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 77 of 100 people found this instruction helpful
The door had always opened with the wrong swing and it wasn't til I needed to repair this that I noticed you could change the swing. I changed the swing of the door and then noticed that the clip was included on both sides so i did not need to repair the catch. I still have the part so when it breaks again, I can just pop it in. read more