YKHMS155LSS0 KitchenAid Microwave - Instructions

I just looked at the broken one to see where it broke and looked at the microwave. I realized that there were two screws that were supposed to hold the vent grill along with 3 slots on the bottom. I inserted the slots on the bottom into the preset spaces for them, lined up the top with the two screws and screwed them into place. Checked to make sure the screws were not too tight and that was it. New vent grill in place and ready to go.

Removed cover (lots of screws), Removed base, Removed inside covers to epose transformer, HV diode, capacitor and Magnetron. Removed HV transformer and labeled wires. Removed door switch. Removed Magnetron and replaced. Re-installed door switch and HV transformer. Connected wires and re-installed internal covers. Installed base and tested unit. Installed cover and re-installed Microwave. Has been running a week just fine. Take a lot of pictures with your phone during the whole process. This will help with getting things back exactly as factory.

I called the repair/parts number to make sure I had correct parts and the young lady instructed me as to the size of the serving tray; within 48 hours we had the VERY carefully wrapped carton opened and back in the microwave, working perfectly. Thank you. We'll recommend you to our friends!

Slid them out and slid them in. Best part - ordered them at Noon on the Friday after the 4th of July and they arrived at 12:10 the next day - standard shipping.

Ordered new vent part. Just set in place and fastened screws. These parts do not last because the plastic does deteriorate.

Simply removed and replaced 2 screws. Have ordered from this site before and have been pleased with service.

1. Unplug the power cord from the wall socket. 2. Remove the 10 screws holding the bottom cabinet cover in place. The bottom cabinet cover will swing down allowing acces to the inside ofe the microwave. 3. Remove the connector from the turntable motor. 4. Use a T15 Torx driver to remove the 2 Torx screws holding the motor in place. 5. Remove the motor. 6. Reverse the process using the new motor.

All I had to do was lay the new tray in the microwave. Easy as pie. Also, the new tray arrived very quickly.

removed 2 screws on vent. Door removed 3 screws on inside of door frame that's it repaired

The front panel is held in place by 3 screws on the right edge of the door. Remove the screws then carefully pry off the front panel from the door. This takes some doing so as not to put too much stress on the door itself as you pry the panel off. The back of the panel is snapped into the door so it isn't easy to pry off. Once you have loosened the panel be careful that the glass window and its frame behind the panel does not fall out and crash to the floor. Once the panel is removed and the glass window and frame are safe, you will see 2 self tapping screws on the back of the front panel that holds the door handle to the front panel. I ordered 2 new screws but they were machine screws, not self tapping. Make sure you keep the old screws! Screwing in the self tapping screws to the new handle was not easy. Be sure you have the proper size screw driver so as not to strip the heads. It takes a lot of pressure to get the screws all the way into the handle. Make sure the glass panel and frame are set in properly than push the frame on to the door so it snaps in all the way around. I worked from left to right as I tapped the panel in place. Once it's in place and the screw holes on the panel and door frame line up replace the 3 screws and you're done.

Remove the old door panel by first removing the three screws on the right-hand-side (rhs) of the door.Then pry the old door panel off by using a flat-blade screwdriver. Begin at the rhs near the door handle. The door panel is attached by being pressed into plastic fingers. Once the door panel is loosened from the plastic clips, you should find that it hinges out from the hinge side of the door. If you are just replacing the door panel you will need to remove the plastic retainer and glass plate in the old door panel. These also are retained by plastic clips. You then need to remove the door handle from the old panel since you will attach this to the new door panel. I suggest putting a reasonably large washer on each of the two screws that hold the handle since it is the stress caused by these two screws that caused your old door panel to crack. The washers distribute the stress on the door over a larger larger area. Snap the glass plate from the old panel into the clips on the new door panel. Secure the glass plate with the plastic retainer than you removed from the old door panel. Begin installing the new door panel complete with the glass plate and plastic retainer by first placing it over the hinge side end of the door. The plastic tabs in the door panel should fit into recesses on the lhs of the microwave. Then gently begin pressing the new door panel into the plastic clips on the microwave frame. Work from the hinge side to the door handle side. Congratulations - you have just saved yourself $300+ on the purchase of a new microwave oven!

Make sure that the screws go in the holes, after you put the grill in place.

Replaced with new parts

Removed screws from microwave case. installed new grille. inserted screws into holes in case. Tightened screws to secure grille

Arrived in 24hours!!! Great.