YKGST307HW8 KitchenAid Range - Instructions

I turned off the breaker (I'm a little nervous even unplugging a 220 plug). I first removed the cover from the back of the stove to get to the wiring/socket. Removed the two wires from the leads - they just pull off by hand but use a needlenose pilers if it is stuck. One is larger so no need to try to remember which one goes where. I removed the glass cover and bulb from inside the oven. I read another post on this site that said there were clips that you had to press to get the old socket out which helped. That part was a little tricky as the insulation around the socket makes it hard to see and the opening is really tight. I finally found the clips and pressed one then got that side out enough to hold the clip back then pressed the other clip and I was able to push it right out. I did not have the strength to press both clips with enough pressure but if you do, that would probably be easier. From inside the oven, I pushed the new socket through the hole - there was a little notch in the opening that had to match up with the socket. I had to push pretty firmly until I felt both clips snap in place. Replaced the wires, turned on the power, screwed in the bulb and cover and I had light!

real easy one to take care of, when the drawer broke I thought it was more than what it really was, after looking at it and seeing the wheel was gone I ordered the part and it came very quick, drawer is now fixed.

Never repaired an oven before, I just used a screwdriver and went slowly taking this over door apart to replace this glass. I just took piece by piece apart until the glass came out and retraced my steps to install the new glass. Sure glad I did this myself, a new convection oven stove would easily set me back 1,500.00 and......save a bundle on service call fees.

All I had to do was unscrew the pyrex lens over the oven light and then remove the old gasket and replace it with the new one. Worked like a champ!

Purchased 2 piece broiler pan from this site

No repair. I've used the new one and like the one that cracked on the wiring it works beautifully. I APPRECIATED THE VERY QUICK RESPONSE FROM YOU AS I RECEIVED IT IN ONLY 2 DAYS. THANK YOU

I went online and discovered the repair method and schematic of the range. I removed the spark module after first removing the upper rear panel cover and replaced with the new part module ordered from your company and now the spark module operates all the gas elements when they are turned on thus lighting the gas burners. My mother in law was thrilled, as she had been using matches and burning her finger tips,since the original range part malfunctioned. The only problem was the small screw from the original installation was not long enough , so it required some changes to get it affixed to the cabinet side.Thanks for the reasonable price and the right part for the job!!

I just put the grate pads in the bottom of the grate. The repair was a snap.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

I read it may be the temp sensor. Ordered a new one. Took a minute to undo three screws holding the back on, and one screw for the sensor. But still didn't work. Then realized maybe the oven was changed to Celsius. In manual - open door, hold broil for seconds and changed back to Fahrenheit.

Removed the door just like you would do when cleaning the oven; I placed the door on a blanket on the kitchen table and carefully disassembled the door. There were more parts than I expected so keeping track of where everything went was important. I might add that without the use of my cordless variable speed drill motor removal of some of the screws would have been difficult. Adding the weight of the drill motor with sufficient push power I was able to tap the switch which "snapped" the screw loose. Don't think I could have done it with a hand type screw driver without stripping the head. Knowing your tools is very important.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation

Original bumper pads NOT glued into the burner grates. Hence they began to disappear during routine use and cleaning. Very simple repair with a little glue this time around. But fairly expensive for a very small part set