Quick Question!

Have you ever purchased from PartSelect.com before?

Models > YKERS205TB0

YKERS205TB0 KitchenAid Range - Overview

Get Parts and Repair Help for YKERS205TB0

If you know the range repair part you need, you can browse the list of all parts on the YKERS205TB0, or you can search by name or part description. You can also find your part by where it is located on the YKERS205TB0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for YKERS205TB0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Manuals & Care Guides for YKERS205TB0

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.88

Light Bulb - 40W

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these repla...

$29.74

Long Oven Sensor

This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approximately 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.

$3.02

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$6.49

Levelling Leg

This is a levelling leg for your oven, range, or stove. It is just under 3 inches long, is all black in colour, and is made entirely out of plastic. The levelling legs on your oven allow your appliance to sit perfectly flat. The new one may be longer in length than your original, but will work the same. Install the new leveling leg, and test if you have it adjusted properly by putting the appliance on four legs. Adjust in or out as required if your oven is rocking. It is recommended to check the other three levelling legs on your appliance in case they are also damaged or worn.

$71.26

Bake Element - 3600W

This bake element is found on the bottom of the oven.

$19.00

Burner Control Knob - Stainless

This knob accepts a D-shaped shaft. Sold individually.

$66.33

Inner Door Glass Pane

Glass only.

$19.90

Terminal Block

This part is for oven ranges, it connects individual wires and protects the device from electrical surges, voltages, and current. With this part, the house power is connected to the range wire harness. Some symptoms replacing the terminal block could be a solution for are little to no heat when baking, element will not heat and/or it will not start. This part will prevent loosening and will reduce damage caused by corrosion (by two different metals). Refer to the instructional diagram for further replacement guidance and exact placement. You must unplug the appliance before installing this part and wear gloves to protect your hands.

$7.40

CLEANER

This bottle of non-abrasive cooktop cleaner breaks down and gets rid of the hardest baked-on stains and residue without causing any harm to your appliance. The bottle is 10 oz and ...

$4.94

Double Sided Tape

Part differ in appearance or color, but functions same as original.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 120 of 139 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

Right rear burner went bad

  • Customer: Mark from Loxahatchee, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 114 of 124 people found this instruction helpful
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip char... read more

Oven wouldn't get hot enough

  • Customer: Shawn from Atlantic Highlands, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 105 of 114 people found this instruction helpful
First and MOST IMPORTANTLY, I located the breaker switch for my oven and turned it off. I verified this by noticing that the electric clock on the oven display was no longer powered.

After removing all the oven racks, I removed the two screws at the bottom of the back end of the oven holding the metal "floor" in place.

Removing the... read more